Lower the door and dismantle it by removing the hardware. Lower a double door by recruiting at least two helpers to help with the weight, and place a 2×4 block under the door to prevent smashing a foot or finger when it’s lowered. Remove the sections one at a time by disconnecting the rollers and brackets. If you have windows, tape them to help control flying shards if they break. Then remove the old roller tracks and remaining hardware.
The tech that serviced your door must not understand simple mechanics. The tracks do not move, so they do not need to be lubricated. All that does is make a mess. The rollers and hinges DO move, so it is logical to lubricate them, at the hinge barrel or pivot point, and in the little area near the stem of the rollers where you can see the bearings. Adding a bit of lube to the torsion spring also cuts down on the friction between the coils and makes the spring glide easier. However, too much will make it spritz out lube as the door opens and closes, and that it less than desirable. Same thing for pulleys on an extension spring door.

After you’ve ordered your new garage door, we’ll perform a site inspection to confirm your door size. We’ll contact you to schedule the installation, and our professional installers will do the rest. They’ll deliver your door, take down the old door, reconnect your opener if there is one, seal your perimeter and provide a final walk-through where they’ll clean up the area and haul away your old door. Additional fees for haul away may apply in some markets. We are happy to provide answers to questions you may have at the time of your garage door and opener installation.


Safe automatic door openers. All automatic openers must now have an auto-reversing mechanism and photoelectric eyes located near the floor on both sides of the door (see photo). If the door is closing and the beam between the eyes is interrupted, the door will automatically reverse. If the eyes aren’t connected, the door won’t operate. For instructions on how to install a new garage door opener, see How to Install a Garage Door Opener.

If the light attached to the door opener mechanism blinks several times after the door reopens, this generally means something is blocking the sensors or that they've become misaligned.  The two sensors are generally clipped onto the door track about six inches from the floor. You can move them slightly with your hands to try to get them lined up.   Other possibilities include a broken cable that must be replaced, a track that is bent and needs to be replaced or a worn extension spring cable pulley that needs to be replaced.
Whether your garage door problem requires a replacement or repair of the door itself or any of its components, our technicians will be able to advise you on the most cost-effective and appropriate solution. We oftentimes get called for quick fixes of broken garage door springs, broken rollers and bent garage door tracks; repairs of garage door openers and cables; replacements of garage door drums and panels; insulation installation as well as tune-ups and inspection. Whatever is the prob-lem with your garage door, we can definitely handle it. Our team of technicians are highly trained and experienced in any type of emergency garage door service. Whatever the make or model, they will be able to diagnose the problem, offer you solutions and immediately fix the issues. They do it well and they do it fast. That’s A1 service for you!
Ricky appeared promptly at our appointment time, did a thorough safety inspection of our existing garage door opener, and explained the problems he found. Upon deciding to replace the door, he provided a complete and easy to follow set of options and samples from which to make our decision. Placing the order was a simple procedure, and Ricky was very knowledgeable and professional throughout our meeting with him.read more
Ryan Fleming, Technician with Precision Door replaced a broken garage door spring at our home last night and I was so impressed with his knowledge, professionalism and positive attitude that I felt compelled to write this review. We have been customers of Precision Door for over 5 years and have always been pleased with how promptly and cost effectively they perform repair and maintenance work. I highly recommend both Ryan and Precision Door.read more
Carriage: These doors mimic the look of doors found on old carriage houses in the days of horses and buggies. Because of their rustic look, they are often favored in the West and Southwest of the United States. The doors swing open like oversized French doors and hang from jambs on hinges. With their unique look, they create an area of visual interest for your home and are quite energy efficient. The downside is they require a considerable amount of clearance to work properly. Because most carriage garage doors are largely composed of wood, you may need to replace deteriorating or rotting door materials. The average cost for carriage garage door repairs is $133.
A torsion spring counterbalance system consists of one or two tightly wound up springs on a steel shaft with cable drums at both ends. The entire apparatus mounts on the header wall above the garage door and has three supports: a center bearing plate with a steel or nylon bearing and two end bearing plates at both ends. The springs themselves consist of the steel wire with a stationary cone at one end and a winding cone at the other end. The stationary cone is attached to the center bearing plate. The winding cone consists of holes every 90 degrees for winding the springs and two set screws to secure the springs to the shaft. Steel counterbalance cables run from the roller brackets at the bottom corners of the door to a notch in the cable drums. When the door is raised, the springs unwind and the stored tension lifts the door by turning the shaft, thus turning the cable drums, wrapping the cables around the grooves on the cable drums. When the door is lowered, the cables unwrap from the drums and the springs are rewound to full tension.[7]
Sectional: Also known as a raised panel door, this door is the most common. It is made of several horizontal panels hinged together, fitted with wheels and mounted within a track. The biggest advantage of this door is it takes up relatively little space and easily controlled with a standard remote garage door opener for a nominal cost. Their moving parts are readily accessible which can keep repair costs low. The average cost for sectional door repairs is $128.
For Sears Garage Door Installation and Repair Services, making your garage door safe is as important as making it function well. For this reason, all of our repair services and tune-ups feature a 20-point safety check. Our technician will carefully examine your garage door panels, springs, sensors, safety release, hardware, track, and more. This ensures that, not only has our work been done well, but that your garage door poses no danger to your vehicles or family. Due to the intricacy of garage door systems, only garage service professionals should attempt to adjust, repair, or service door equipment.
They sent Doug Fussell out to my house on the day after Christmas! I had only called them three days before! Doug was a premier technician, very thorough and very efficient. I expected him to take two days, since he was replacing two doors and adding openers on each door. He only took the daylight hours of one day! I could not believe how fast he was! In addition, he thoroughly taught me how to use the remote openers. I highly recommend them to anyone!

Garage Door Opener

×