Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.
I was very impressed by the high level of knowledge and how thorough options were presented. I was provided with a quote for a complete set of doors and accessories, a replacement of existing doors. I can honestly say compared to others James (Precision) has my utmost confidence. I am going to have Jim return so we can go over the quote and I want my wife to choose the window patterns. Very impressed.
Garage doors cause injury and property damage (including expensive damage to the door itself) in several different ways. The most common causes of injury from garage door systems include falling doors, pinch points, improperly adjusted opener force settings and safety eyes, attempts at do-it-yourself repair without the proper knowledge or tools, and uncontrolled release of spring tension (on extension spring systems).
Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.
Mike did an outstanding job replacing two torque-master spring assemblies for my double door garage. He arrived early, after calling to say he could do so, and offered a concise explanation of his very thorough safety inspection and diagnosis of my problem (one broken spring and another of suspect reliability). He then proceeded to swap out both torque masters with new torsion bar mechanisms in less than two hours. I found him personable, articulate, knowledgeable, and efficient. Honestly, my confidence in these newly installed devices has more to do with Mike than the products themselves. Thank you, Precision, for sending such a qualified professional to repair my garage doors. I will not hesitate to recommend your services to friends.read more
Roller doors ("Sheet Doors"-USA) are usually constructed of corrugated steel. They evolved from cover window and door coverings.[4] Other materials can be used (e.g.; transparent corrugated fibreglass) where strong impact resistance is not required. Corrugations give the door strength against impacts. A typical single car garage roller door has a preloaded spring inside the rolling mechanism. The spring reduces the effort required to open the door. Larger roller doors in commercial premises are not sprung (except USA) and use a manual pulley and chain system or a geared motor to raise and lower (roll up and roll down) the door. Roller doors cannot be effectively insulated.
Step 2: Check the tracks with a level to make sure they're properly aligned. Horizontal tracks should slant slightly down toward the back of the garage; with roll-up doors, the vertical sections of track should be exactly plumb. Both tracks must be at the same height on the garage walls. If the tracks are not properly aligned, loosen but do not remove the screws or bolts that hold the mounting brackets, and tap the tracks carefully into position. Recheck the tracks with the level to make sure they're in the right position; then tighten the screws or bolts at the mounting brackets.
When you install a new garage door, replace all the hardware as well. If your automatic opener doesn’t have an automatic reversing system that includes photoelectric eyes, replace it. Doors with openers also require two extra pieces of hardware that you’ll see in Photo 4: a support strut (usually included in the door kit) and an opener bracket (not included). For doors with torsion springs located over the door, spend the $50 or so to have a garage door professional release the tension.
I had Precision Doors come to my 1937 home to quote a new door to replace the original manual one. Service tech was prompt, patient, listened to my wishes to keep the house "old" in aesthetics, yet new and improved with the highest quality door they use. Joe, my tech, was phenomenal! He offered great advice and solutions to my situation, and even a better price all in. Confidence and trust was built in our very first meeting. The door was painstakingly installed with so many variables of old and new combinations. But Joe was amazing, and the door looks and operates flawlessly. Precision Door's top tier motor and door are the quietest I've ever witnessed. I feel so happy with my dealing with them. It was a great purchase and of the very best quality. One and done! And they offer a lifetime warranty on all of their work. It really can't be better. Have Precision Doors come to your home and you will be pleased that you did.read more

Your garage door is more than just a point of entry for vehicles; it also protects your greatest investment and has a huge impact on your home’s overall curb appeal. So don’t let a worn-down, barely functioning garage door interfere with the form or function of your home! Instead, get in touch with Aladdin Garage Doors today for the reliable garage door repair services your home needs.


Hmmm...Intro to E12...looks suspiciously like a freehand angled cut on that contractor saw... Yes, the riving knife might save you from a dangerous kickback...but still a very bad idea.. Why not a 'safety segment' explaining kickback and why you should not do this (styrofoam demo, back side of the blade teeth rising up grabbing the foam and throwing it back at you...)
If you're like most people shopping for a new garage door you want to accomplish 3 things: Get a really good idea how your new door will look on your home before you buy it. Show it to people you trust to get their opinion and get a price quote. You probably would also like to do all of this quickly and without any sales pressure. If that's true you're in the right spot. The Precision Door Designer will allow you to find the right style door, share a picture of it on Facebook and email your selected options for a free price quote. All in less than 10 Minutes! Select a collection to begin or continue reading to learn more.

Great Garage Door provides quality garage door repair and installation services in Monticello MN. We know you have a lot of options when looking for a reliable service company, and that is why we have the best warranties and guarantees in the business. We stand behind our Minnesota products and services with over 30 years in the business and over 160,000 clients served.  We have a long list of happy clients that were once in your shoes and we’d like to learn how we can help you!

Garage Door Service Company

×