Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
Here is an odd problem that I cannot figure out. I am handy with electrical stuff, but this one has me stumped. My small kitchen appliances all work on a single circuit, with 5 outlets. One of those outlets has a 20Amp breaker built into it with a test and resent button (I never understood what the test button is for). I only have a toaster, a floor lamp and occasionally a coffee grinder plugged into the circuit. Suddenly, none of the outlets work. Nothing new, no new appliances, the whole circuit went dead. I noticed when I trigger the reset button, there is an immediate click and it goes out again. I have tripped and reset the main breaker on the circuit board in the garage, nothing. Power gets to the outlet, but it doesn't work and there is no electricity in any of the 5. I un plugged everything. Reset the breaker on the outlet. It clicked again immediately, still no electricity. I changed out the outlet, with a new one with breaker built in which I bought today at Home Depot. Same problem. I tested for electricity, the outlet with the built in breaker receives 120v electricity coming in, but it always seems to be shorted out and does not send it out. I assume that all of the 5 outlets are connected inline, so thinking that if I went one by one, I'd be able to find a short. I opened all of the boxes, checked everything and all looks clean, new, no problems. I completely disconnected the two outlets that are closest to the main one with thereset button and nothing.Help
Great! We specialize in all sorts of garage door repair work. Working around the garage door can be fairly dangerous if you’re trying to repair this issue on your own. Most garage door companies will quickly remind folks about this, and it’s true. Their are some hazards to watch out for when working around these heavy and high tension doors. We recommend you give an expert a call to address the issue in a safe and timely manner for you.
Extension spring systems should always be restrained by a safety cable that runs through the middle of the spring, tying off to a solid point at the rear and front of the horizontal door track. Extension springs represent a hazard to bystanders when a spring, pulley, or cable breaks under tension. Metal parts from extension spring systems can suddenly be launched.
Should an object or individual become trapped, or if a malfunction occurs, pulling on the handle will allow the user to manually lift the door up or down. If a garage door is good working order, the spring system that runs across the top of the door opening should provide enough assistance so an average adult can lift the door with relatively little effort.
A torsion spring counterbalance system consists of one or two tightly wound up springs on a steel shaft with cable drums at both ends. The entire apparatus mounts on the header wall above the garage door and has three supports: a center bearing plate with a steel or nylon bearing and two end bearing plates at both ends. The springs themselves consist of the steel wire with a stationary cone at one end and a winding cone at the other end. The stationary cone is attached to the center bearing plate. The winding cone consists of holes every 90 degrees for winding the springs and two set screws to secure the springs to the shaft. Steel counterbalance cables run from the roller brackets at the bottom corners of the door to a notch in the cable drums. When the door is raised, the springs unwind and the stored tension lifts the door by turning the shaft, thus turning the cable drums, wrapping the cables around the grooves on the cable drums. When the door is lowered, the cables unwrap from the drums and the springs are rewound to full tension.
Steel entry doors - when a garage is being fitted with new doors, it is also a good idea to consider a separate single 3x68 exterior door with half-glass and locksets too. These may require some carpentry, but they are a good way to allow for some flexibility in the choice of larger garage door, and can ensure that the homeowner will have more than a single way in or out of the structure. The average costs for such a feature range from $250 to $1000 each.
"The doors, tracks and openers were installed in a few hours. They look great and add so much to our exterior as well as quiet and warmer in the garage. The technicians tweaked the pad installation as we needed. They were on time, professional and courteous. I give them 5 stars. My only ding on performance was filling up our rolling recycle bin with intact noses that we had to pull out and break down. I thought the boxes would have been hauled away."
Both springs broke on my double door, and I had no idea who to call. I asked my smart phone for garage door repairs and they gave me one company listed in Lebanon. I called and set up an appointment with the tech and he said he would be there in an hour. After 4 hours I called and they got me to the tech and here is what he said after my 4 hour wait: "We can't do that, you will need to call someone else." I asked if he needed to reschedule, and he said, "No, call some other company." My temperature was high and I looked on my computer and Precision came up on the screen. I looked it over real good, checked the reviews and called them on Saturday morning. They said a tech could be out by noon. The tech called at 10:30 and said he could be here by 11am if that was alright. It was. John showed up at 11, we greeted each other, I felt good as soon as I met him. He looked over the door, sure enough both springs broke, cable off. He gave me 3 options: just fix the springs and cable; do that and change out the rollers which were clearly rusted and lots of play; and do that with a life-time warranty. No pressure, he was ready to do whatever I said. I told him the first option for now, and he went right to work. My wife and I discussed that our door was over 14 years old and has had no maintenance at all, and we decided to have the warranty. No problem. John was through and thorough in no time at all. The door sounded amazing, we had gotten so used to the noise, until it was not there any more - smooth and quiet and efficient. I am so thankful the other company blew me off, so that I came in contact with Precision. Great job. I will recommend them to everyone. 5 STARS ALL THE WAY!
Call Precision for garage door repair in the Spokane area. We will send an expert garage door repair technician to your home that same day in order to repair your door on your schedule. Our technicians are experts in one area and one area alone: garages. Don’t stress over having to find a repairman who might not know garage doors all that well and trust your repairs to a company that guarantees the best service and parts in the business.
When your home or business depends on garage door repair in Bakersfield for everyday convenience, security, and dependability, the need for repairs can be a serious slowdown in your life. That’s why King Door Company offers Kern County residents and business the best garage door repairs and other services, completed by a team of expert professionals who can quickly and effectively fix garage doors in Bakersfield and the surrounding communities in Kern County.