Test the door balance. A garage door should require only a few pounds of pressure to move it up and down. If springs wear out and lose their resiliency, a power garage door opener may need to work extra hard to lift the door. This can quickly wear out the motor on the opener. Replacing worn-out springs is usually a job for a professional technician.
Garage doors cause injury and property damage (including expensive damage to the door itself) in several different ways. The most common causes of injury from garage door systems include falling doors, pinch points, improperly adjusted opener force settings and safety eyes, attempts at do-it-yourself repair without the proper knowledge or tools, and uncontrolled release of spring tension (on extension spring systems).

The tech that serviced your door must not understand simple mechanics. The tracks do not move, so they do not need to be lubricated. All that does is make a mess. The rollers and hinges DO move, so it is logical to lubricate them, at the hinge barrel or pivot point, and in the little area near the stem of the rollers where you can see the bearings. Adding a bit of lube to the torsion spring also cuts down on the friction between the coils and makes the spring glide easier. However, too much will make it spritz out lube as the door opens and closes, and that it less than desirable. Same thing for pulleys on an extension spring door.


The lightweight design also causes a decrease in the insulation of these doors, so individuals that live in colder climates may want to consider other options for their garage door needs.  Fiberglass does not corrode when subjected to salt-water like some other door styles out there.  Individuals that live in coastal areas will find this feature beneficial for their needs.

Roller doors ("Sheet Doors"-USA) are usually constructed of corrugated steel. They evolved from cover window and door coverings.[4] Other materials can be used (e.g.; transparent corrugated fibreglass) where strong impact resistance is not required. Corrugations give the door strength against impacts. A typical single car garage roller door has a preloaded spring inside the rolling mechanism. The spring reduces the effort required to open the door. Larger roller doors in commercial premises are not sprung (except USA) and use a manual pulley and chain system or a geared motor to raise and lower (roll up and roll down) the door. Roller doors cannot be effectively insulated.


Lower the door and dismantle it by removing the hardware. Lower a double door by recruiting at least two helpers to help with the weight, and place a 2×4 block under the door to prevent smashing a foot or finger when it’s lowered. Remove the sections one at a time by disconnecting the rollers and brackets. If you have windows, tape them to help control flying shards if they break. Then remove the old roller tracks and remaining hardware.
Install the vertical roller tracks first by wrapping the curved lip around the rollers. The top of these tracks should be approximately 8 in. below the top of the top section. Wait to install the upper tracks until this step is complete. Check the level of the top section to make sure the tops of the vertical roller tracks are level with each other. The bottom of the roller tracks should be at least 1/8 in. off the concrete floor. After leveling and mounting these tracks, install the upper roller (horizontal) tracks.

Here is an odd problem that I cannot figure out. I am handy with electrical stuff, but this one has me stumped. My small kitchen appliances all work on a single circuit, with 5 outlets. One of those outlets has a 20Amp breaker built into it with a test and resent button (I never understood what the test button is for). I only have a toaster, a floor lamp and occasionally a coffee grinder plugged into the circuit. Suddenly, none of the outlets work. Nothing new, no new appliances, the whole circuit went dead. I noticed when I trigger the reset button, there is an immediate click and it goes out again. I have tripped and reset the main breaker on the circuit board in the garage, nothing. Power gets to the outlet, but it doesn't work and there is no electricity in any of the 5. I un plugged everything. Reset the breaker on the outlet. It clicked again immediately, still no electricity. I changed out the outlet, with a new one with breaker built in which I bought today at Home Depot. Same problem. I tested for electricity, the outlet with the built in breaker receives 120v electricity coming in, but it always seems to be shorted out and does not send it out. I assume that all of the 5 outlets are connected inline, so thinking that if I went one by one, I'd be able to find a short. I opened all of the boxes, checked everything and all looks clean, new, no problems. I completely disconnected the two outlets that are closest to the main one with thereset button and nothing.Help
Garage Door Installation – This includes the installation of a new garage door. Includes the door itself, the track, cables, springs, hinges, handles, locks and rollers.  It is the complete service and installation of a new door. We inspect all the parts, make adjustments to fit your garage opening, and service all elements during the installation process. Plus, we check to ensure all parts are in proper working order after installed.
On Monday afternoon the spring on our garage door snapped when the door came down after we had just backed out. As we were heading to a doctors appointment I did nothing about it until Tuesday morning. I called Precision Garage at about 8:30 am and their technician Aaron was at out home before 10am. He did a complete inspection and told us what was needed and also gave us an estimate on replacing the door as we have been thinking about that for sometime. He was very thorough and courteous. He explained everything to us. We decided to have new springs put in and order a new door. The springs were in within 20 minutes and we now have use of our door. They said it would be about three weeks for the new door to arrive and then they will install. We were blown away that we could get such quick service and so professional.There was no pressure and he went into detail about each kind of door that was available. Precision Garage is truly a great Thanksgiving gift for us. I'm anxious for the new door to come and I know we will love it.read more
A standard double garage door is 7 ft. high by 16 ft. wide. Standard single doors are 7 ft. high by 8 or 9 ft. wide. Because the doors are so large, few home centers and only some garage door stores keep many doors in stock, so expect to order one instead of buying it off the shelf. Garage doors are available in wood, fiberglass and steel. Steel doors, like ours, are light, maintenance-free, affordable, readily available, and have an insulating value as high as R-19.
The electronics should also be inspected before or after investing in the cost of replacing the garage door panel to make sure your door will operate properly. The sensors prevent the door from closing on someone's foot or a pet. If they don't work, someone could be injured. Also check to make sure the door opener works, since you could otherwise be locked out of your garage.

They sell insulation kits at the local big box hardware store and I cringe every time I see them. The box weighs about 15 pounds, which doesn't sound like a lot. It is definitely enough to un-balance a garage door. The springs are calibrated for the weight of the door, and adding weight makes the door "heavy" for the springs. This means that if you pull an operator disconnect handle when the door is in the open position, the door is likely to descend much more quickly than you anticipate. People have been hurt when a garage door came down on them and the momentum knocked them over. Only add weight if the door springs can be re-torqued or replaced with springs of the proper pull.

I saw the plans during the Q&A of this proposed restructure and it seemed odd to me that the homeowners added a second story only above half of the house. I would think since they're must be spending around $700k for the project they should spend a little more and do the second floor above the whole house even if they only finish what is proposed now on the second floor they'd still have an unfinished area for the future home owners or for them to tackle when money is available. It would be a definite bump to the house value during the time of sale. Unless this has to do with zoning and FAR/lot size... 
×