Wood was the first material used in the manufacturing of garage doors. This type of material is still one of the most desired by homeowners. Individuals will find that garage doors that are constructed from wood can be painted or stained to match their home’s look. However, without regular maintenance, wood is susceptible to rot, decay and insect infestation.

Question- I bought a Clopoy coachmen series 8' garage door last April , over the winter the bottom panel got a dent in it [snow blower-rock?] It is about the size of an egg . Called to see if any repair can be done instead of replacing[similar to dent wizard for autos and was advised cant be done and had to replace 3 panels? not going to do that- is there any other opinions on this?
Single panel doors are constructed from one monolithic panel. From the closed position a single panel door swings up and overhead with a hinge on each side (known as jamb type hardware) to the fully open position. A disadvantage of monolithic panel doors is that the swing up arc of the door occurs partially outside the garage. This means a vehicle must stop and park several feet in front of the door to avoid being hit by the garage door when it is opened.
Step 2: Check the tracks with a level to make sure they're properly aligned. Horizontal tracks should slant slightly down toward the back of the garage; with roll-up doors, the vertical sections of track should be exactly plumb. Both tracks must be at the same height on the garage walls. If the tracks are not properly aligned, loosen but do not remove the screws or bolts that hold the mounting brackets, and tap the tracks carefully into position. Recheck the tracks with the level to make sure they're in the right position; then tighten the screws or bolts at the mounting brackets. 

One of the last safety features on a garage door system is the manual release mechanism. Designed to disengage the garage door from the opening system should entrapment, a power outage or other malfunction occur, the manual release mechanism is most commonly found on the track that runs from opener to the garage door. It’s usually a bright red handle that should hang no higher than 6 feet off the ground.
Technician gave me a window of 1-4pm, I called at 330 to see if he was on his way. He told me he would be there at 4pm, reason being was because of the amount of work orders he had that day. He was also by himself, had no helper. I was very satisfied that he was able to repair my garage door. He was very professional considering he showed up on a Friday afternoon on a 100 degree day. Thanks again
Installing an overhead garage door requires a few tools and a friend to help. First, the lower door panel needs to be set up in the center of the doorway. The remaining panels and tracks are held in place with hinges, brackets, and screws. Set up an easy-to-install torsion spring system to ensure that your door lifts properly for many years to come.
The tech that serviced your door must not understand simple mechanics. The tracks do not move, so they do not need to be lubricated. All that does is make a mess. The rollers and hinges DO move, so it is logical to lubricate them, at the hinge barrel or pivot point, and in the little area near the stem of the rollers where you can see the bearings. Adding a bit of lube to the torsion spring also cuts down on the friction between the coils and makes the spring glide easier. However, too much will make it spritz out lube as the door opens and closes, and that it less than desirable. Same thing for pulleys on an extension spring door.
I saw the plans during the Q&A of this proposed restructure and it seemed odd to me that the homeowners added a second story only above half of the house. I would think since they're must be spending around $700k for the project they should spend a little more and do the second floor above the whole house even if they only finish what is proposed now on the second floor they'd still have an unfinished area for the future home owners or for them to tackle when money is available. It would be a definite bump to the house value during the time of sale. Unless this has to do with zoning and FAR/lot size...
Through our garage door configurator by Clopay, you can design, visualize and purchase a new Clopay garage door. Upload a photo of your home and then browse the configurator to see which style works for you. Choose from a variety of designs, textures, colors, finishes, window options and decorative hardware. You’re able to easily and quickly see the transformation, and then make it a reality.
Jerrod the technician had answers to all my questions. He was very knowledgeable and very patiently explained what was going on with my garage door and the opener. I would definitely recommend A1 garage door service to friends and family. I was given options to either repair the door or replace it. I will get the door replaced when it gets non-functional from A1 garage door service.
To help prevent garage door problems from occurring, the Institute of Door Dealer Education and Accreditation recommends monthly maintenance, including testing that the garage door opener is operational and inspection of the springs, rollers, pulleys, cables and track. Wipe down the tracks, preferably with a microfiber cloth to prevent lint from being left behind. Also, make sure to keep all the metal moving parts lubricated. However, do not lubricate plastic parts. Never reuse an old track with new panels.
Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
×