Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.
Just in case you still want to know: You could glue foam panels to the inside of the door, but it would be better to just pressure fit them in place to avoid the weight of the glue. Any weight that you add to the door has the very real potential to unbalance the door. If the springs were a little "hot" or strong to start with, it may not be a bad thing to add weight. If the springs were the right ones, even a few pounds will un-balance the door. If they were too weak to start with, any additional weight is going to make it worse.

A torsion spring counterbalance system consists of one or two tightly wound up springs on a steel shaft with cable drums at both ends. The entire apparatus mounts on the header wall above the garage door and has three supports: a center bearing plate with a steel or nylon bearing and two end bearing plates at both ends. The springs themselves consist of the steel wire with a stationary cone at one end and a winding cone at the other end. The stationary cone is attached to the center bearing plate. The winding cone consists of holes every 90 degrees for winding the springs and two set screws to secure the springs to the shaft. Steel counterbalance cables run from the roller brackets at the bottom corners of the door to a notch in the cable drums. When the door is raised, the springs unwind and the stored tension lifts the door by turning the shaft, thus turning the cable drums, wrapping the cables around the grooves on the cable drums. When the door is lowered, the cables unwrap from the drums and the springs are rewound to full tension.[7]


Garage doors provide one of the major entryways into your home. Therefore, it is essential to ensure that they are secure and in good working order. If you are having problems with your current door, then you need to have a professional determine if it can be repaired or if it will need to be replaced. Here are some of the most common factors that will affect the cost of a garage door repair.
Great Garage Door provides quality garage door repair and installation services in Monticello MN. We know you have a lot of options when looking for a reliable service company, and that is why we have the best warranties and guarantees in the business. We stand behind our Minnesota products and services with over 30 years in the business and over 160,000 clients served.  We have a long list of happy clients that were once in your shoes and we’d like to learn how we can help you!

"We had an unusual repair requirement. We have horizontal sliding steel doors on our 1950's equipment shed. The upper track was damaged by a roofer's forklift while they were loading supplies onto the roof. The track is made out of very heavy steel, not like the track in today's doors. Toby, responded to my request very quickly and came out of his way to inspect the damage. Although it was not something that he had encountered before, he was able to fix the track and the door is operating better than it has in years. Thank you."

A common material for a new garage door is steel sheet formed or stamped to look like a raised panel wooden door. Steel doors are available in uninsulated, insulated, and double skin steel. A design mimicking carriage house doors has become popular since early 2000s, and many manufacturers clad the exterior of a steel door with composite, vinyl boards, or other trim to give it the appearance of wood.


Step 5: Check for loose hardware, and tighten as needed. On swing-up doors, check the plates where the spring is mounted to be sure the screws are tight, and tighten any loose screws. On roll-up doors, check the hinges that hold the sections of the door together; tighten any loose screws, and replace any damaged hinges. Sagging at one side of the door can often be corrected by servicing the hinges. If a screw hole is enlarged, replace the screw with a longer one of the same diameter, and use a hollow fiber plug, dipped in carpenters' glue, with the new screw. If the wood is cracked at a hinge, remove the hinge and fill the cracks and the screw holes with wood filler. Let the filler dry and then replace the hinge. If possible, move the hinge onto solid wood.
My garage door broke on a Saturday night as I was getting ready to leave for a holiday party. Kelvin was here within 30 minutes. He reviewed everything with me that was happening with my door. He gave me the estimates of what was immediately needed to be done in order for my door to raise and then what I will need to have done very soon. I could see all the problems he pointed out to me and I decided to have everything done. He completed everything that night. I was very satisfied with Kelvin’s professionalism and the work he did. Thank you again.

Spring Issues - Unless it is due to an obstruction of some type, uneven movement of your garage door is likely caused by a problem with the spring mechanism. Roll-up doors generally have one center-mounted torsion spring. The tension on torsion springs is great. Therefore, it is necessary to call a professional for any repairs to this type of spring mechanism to avoid serious injury. Because replacement of these springs or cables in a garage door can take at least two or three hours of labor, costs can average $300 or more.
One aspect of hiring a garage door professional that differs, however, is emergency service. If you need after-hours or weekend service for a damaged or malfunctioning garage door or opener, be sure to ask your garage door contractor upfront about emergency service call fees, which can cost hundreds more than regular services. Unless it’s absolutely necessary, you may save significant money by scheduling garage door repairs and services during normal business hours.

Mike did an outstanding job replacing two torque-master spring assemblies for my double door garage. He arrived early, after calling to say he could do so, and offered a concise explanation of his very thorough safety inspection and diagnosis of my problem (one broken spring and another of suspect reliability). He then proceeded to swap out both torque masters with new torsion bar mechanisms in less than two hours. I found him personable, articulate, knowledgeable, and efficient. Honestly, my confidence in these newly installed devices has more to do with Mike than the products themselves. Thank you, Precision, for sending such a qualified professional to repair my garage doors. I will not hesitate to recommend your services to friends.read more
In many homes, the original garage door was installed during construction of the garage and the builder may have chosen the least expensive model. Decades later, the homeowner may decide to upgrade to a higher quality door. While appearance and cost will likely be the biggest considerations for most homeowners, other factors such as insulation value, ease of operation and safety features should also be considered. A highly rated garage door installation professional can offer more detailed advice.
Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.
If you have a steel door, but want the look of a wood one, it is not necessary to change your entire garage door. Often, it may be possible to mimic the look of wood with skillful painting. Your local home improvement store may be able to provide good advice about the type of paint and brushes needed to mimic the look of wood for your particular door material.

Go for the look of wood with less upkeep with low-maintenance faux wood composite & steel garage doors from our Canyon Ridge® & Coachman® Collections. Our Gallery, and Classic Collection garage doors are also available with Ultra-Grain®, a wood look durable paint. If you’re looking for a more traditional look, our Classic™ Collection of steel raised panel and flush panel garage doors complement most home styles. Add one of our many decorative window options to customize the door's appearance and let natural light into your garage.
The tech that serviced your door must not understand simple mechanics. The tracks do not move, so they do not need to be lubricated. All that does is make a mess. The rollers and hinges DO move, so it is logical to lubricate them, at the hinge barrel or pivot point, and in the little area near the stem of the rollers where you can see the bearings. Adding a bit of lube to the torsion spring also cuts down on the friction between the coils and makes the spring glide easier. However, too much will make it spritz out lube as the door opens and closes, and that it less than desirable. Same thing for pulleys on an extension spring door.
With hundreds of moving parts that are all required to work together, it's no surprise that garage doors may need occasional repair and maintenance. Garage door repair services are also required in emergency situations, like when the garage door won't operate and the car is trapped inside or you've accidentally backed into the door when it was closed. Whether it's a specific repair of your garage door opener, a broken spring that needs to be replaced, or a bent or rusted track, The Home Depot's local, licensed service providers can get the job done quickly and efficiently.
A common material for a new garage door is steel sheet formed or stamped to look like a raised panel wooden door. Steel doors are available in uninsulated, insulated, and double skin steel. A design mimicking carriage house doors has become popular since early 2000s, and many manufacturers clad the exterior of a steel door with composite, vinyl boards, or other trim to give it the appearance of wood.
A typical version of an overhead garage door used in the past would have been built as a one-piece panel.[1] The panel was mounted on each side with unequal parallelogram style hinge lifting mechanism. Newer versions of overhead garage doors are now generally built from several panels hinged together that roll along a system of tracks guided by rollers.[1] The weight of the door may be 400 lb (181.4 kg) or more, but is balanced by either a torsion spring system or a pair of extension springs.[2] A remote controlled motorized mechanism for opening garage doors adds convenience, safety, and security.[3]
Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.

They sent Doug Fussell out to my house on the day after Christmas! I had only called them three days before! Doug was a premier technician, very thorough and very efficient. I expected him to take two days, since he was replacing two doors and adding openers on each door. He only took the daylight hours of one day! I could not believe how fast he was! In addition, he thoroughly taught me how to use the remote openers. I highly recommend them to anyone!

Garage Door Opener

×