Clint and James called and checked if my son had any problem with them showing up earlier than planned . No biggie there, they came, they examined , and they brought my sons busted garage door back up to a fully operation system . While the cost was more than myself or my son expected , the results were undeniable . A complete system review showed many worn or weak spots in his 14-15 year old bearings and such . They replaced what was needed and door works great . Next stop my house , all I needed was a replacement door seal . After talking with the tag team , I decided to go for the full Monty , and get an update to my bearings etc. Just to protect my wife in case I am not around to jack hammer a door open with a busted spring . Which would likely not work anyway ! Longer story short ...great outfit , good team , nice guys , job well done !! If you need any garage door work ...Precision Overhead Door is the place to call . Thanks very much for a great job guys ....Tedread more 

Mike did an outstanding job replacing two torque-master spring assemblies for my double door garage. He arrived early, after calling to say he could do so, and offered a concise explanation of his very thorough safety inspection and diagnosis of my problem (one broken spring and another of suspect reliability). He then proceeded to swap out both torque masters with new torsion bar mechanisms in less than two hours. I found him personable, articulate, knowledgeable, and efficient. Honestly, my confidence in these newly installed devices has more to do with Mike than the products themselves. Thank you, Precision, for sending such a qualified professional to repair my garage doors. I will not hesitate to recommend your services to friends.read more
Widths - in addition to doors coming in a range of styles, they can be found as double-width and single-width styles. There are some serious considerations when opting for one over the other. For example, if a homeowner decides to use a single door that covers the entire opening of a two-car garage they will have to make serious structural modifications to the entry way;

Noisy garage doors cause all kinds of problems, especially for anyone who has to sleep above or next to the garage. Fortunately, most noisy garage doors can be fixed with a combination of routine maintenance and the replacement of a few parts. If the basic maintenance tips described above don't quiet a noisy garage door, it's possible that the door's hinges need to be replaced.


Good response time and service; Question - I googled to find the Sears Garage Door repair phone number. During the conversation, I was unsure if this was "Sears" or a "contractor service" or other service. I had to ask if this repair person was coming from "Sears" or an independent repair. I was concerned until the service man arrived in a sears truck wearing Sears apparel. You might want the process to be more clearly identified as Sears.
If you've installed a replacement door or two around your home, it seems pretty simple -- all it takes is tightening a couple of screws and you're done. Installing t­he largest door in your house, however, is not quite so simple. Garage door in­stallation, whether manual or automatic, can be difficult and dangerous. Manual garage door installation is much easier than automatic garage door installation, but the one you choose generally depends on what kind of door you have.

Here is an odd problem that I cannot figure out. I am handy with electrical stuff, but this one has me stumped. My small kitchen appliances all work on a single circuit, with 5 outlets. One of those outlets has a 20Amp breaker built into it with a test and resent button (I never understood what the test button is for). I only have a toaster, a floor lamp and occasionally a coffee grinder plugged into the circuit. Suddenly, none of the outlets work. Nothing new, no new appliances, the whole circuit went dead. I noticed when I trigger the reset button, there is an immediate click and it goes out again. I have tripped and reset the main breaker on the circuit board in the garage, nothing. Power gets to the outlet, but it doesn't work and there is no electricity in any of the 5. I un plugged everything. Reset the breaker on the outlet. It clicked again immediately, still no electricity. I changed out the outlet, with a new one with breaker built in which I bought today at Home Depot. Same problem. I tested for electricity, the outlet with the built in breaker receives 120v electricity coming in, but it always seems to be shorted out and does not send it out. I assume that all of the 5 outlets are connected inline, so thinking that if I went one by one, I'd be able to find a short. I opened all of the boxes, checked everything and all looks clean, new, no problems. I completely disconnected the two outlets that are closest to the main one with thereset button and nothing.Help


Lower the door and dismantle it by removing the hardware. Lower a double door by recruiting at least two helpers to help with the weight, and place a 2×4 block under the door to prevent smashing a foot or finger when it’s lowered. Remove the sections one at a time by disconnecting the rollers and brackets. If you have windows, tape them to help control flying shards if they break. Then remove the old roller tracks and remaining hardware.

Another key safety feature to prevent entrapment from garage doors is the “electric eye” sensor system found on many more modern garage door systems. Sensors placed on either side of the garage door’s track system about 4 to 6 inches off the ground transmit an infrared beam of light during a door’s closing operation. Should anything break the beam during the closing operation – including adults, pets or other objects – the opener should automatically stop and reverse the closing operation.
Step 2: Check the tracks with a level to make sure they're properly aligned. Horizontal tracks should slant slightly down toward the back of the garage; with roll-up doors, the vertical sections of track should be exactly plumb. Both tracks must be at the same height on the garage walls. If the tracks are not properly aligned, loosen but do not remove the screws or bolts that hold the mounting brackets, and tap the tracks carefully into position. Recheck the tracks with the level to make sure they're in the right position; then tighten the screws or bolts at the mounting brackets.

Instead, try other methods that might break the frozen connection between the door and the floor. For example, you can use a heat gun or hair dryer to melt the ice and free the door. Standard de-icing products can also work. And if you are careful not to damage the door or the seal on the bottom of the door, you can use a flat shovel or similar tool to chip away at the ice.


Clint and James called and checked if my son had any problem with them showing up earlier than planned . No biggie there, they came, they examined , and they brought my sons busted garage door back up to a fully operation system . While the cost was more than myself or my son expected , the results were undeniable . A complete system review showed many worn or weak spots in his 14-15 year old bearings and such . They replaced what was needed and door works great . Next stop my house , all I needed was a replacement door seal . After talking with the tag team , I decided to go for the full Monty , and get an update to my bearings etc. Just to protect my wife in case I am not around to jack hammer a door open with a busted spring . Which would likely not work anyway ! Longer story short ...great outfit , good team , nice guys , job well done !! If you need any garage door work ...Precision Overhead Door is the place to call . Thanks very much for a great job guys ....Tedread more
×