Not only was the upward-lifting garage door and the electric garage door opener invented by Overhead Door Corporation’s founder C.G Johnson in the 1920s, but we also have a tradition in excellence for garage door repair, service and maintenance. Even with the most reliable products problems can arise and when they do it’s important to know who to contact to fix these issues while providing solutions to prevent future complications.
Ryan Fleming, Technician with Precision Door replaced a broken garage door spring at our home last night and I was so impressed with his knowledge, professionalism and positive attitude that I felt compelled to write this review. We have been customers of Precision Door for over 5 years and have always been pleased with how promptly and cost effectively they perform repair and maintenance work. I highly recommend both Ryan and Precision Door.read more
Jerrod the technician had answers to all my questions. He was very knowledgeable and very patiently explained what was going on with my garage door and the opener. I would definitely recommend A1 garage door service to friends and family. I was given options to either repair the door or replace it. I will get the door replaced when it gets non-functional from A1 garage door service.
Locating a contractor - there are many professional overhead garage door companies. It is always advisable to contact at least three different agencies and request a bid or quote for the work. Be sure that each quote includes the costs for a few different types of doors, any installation fees, and the cost of wiring the electronic openers. Standard prices range from:
Here is an odd problem that I cannot figure out. I am handy with electrical stuff, but this one has me stumped. My small kitchen appliances all work on a single circuit, with 5 outlets. One of those outlets has a 20Amp breaker built into it with a test and resent button (I never understood what the test button is for). I only have a toaster, a floor lamp and occasionally a coffee grinder plugged into the circuit. Suddenly, none of the outlets work. Nothing new, no new appliances, the whole circuit went dead. I noticed when I trigger the reset button, there is an immediate click and it goes out again. I have tripped and reset the main breaker on the circuit board in the garage, nothing. Power gets to the outlet, but it doesn't work and there is no electricity in any of the 5. I un plugged everything. Reset the breaker on the outlet. It clicked again immediately, still no electricity. I changed out the outlet, with a new one with breaker built in which I bought today at Home Depot. Same problem. I tested for electricity, the outlet with the built in breaker receives 120v electricity coming in, but it always seems to be shorted out and does not send it out. I assume that all of the 5 outlets are connected inline, so thinking that if I went one by one, I'd be able to find a short. I opened all of the boxes, checked everything and all looks clean, new, no problems. I completely disconnected the two outlets that are closest to the main one with thereset button and nothing.Help
All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.
Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
Mechanical garage door openers can pull or push a garage door with enough force to injure or kill people and pets if they become trapped. All modern openers are equipped with “force settings” that make the door reverse if it encounters too much resistance while closing or opening. Any garage door opener sold in the United States after 1992 requires safety eyes—sensors that prevent the door from closing if obstructed. Force settings should cause a door to stop or reverse on encountering more than approximately 20 lbs (9.07 kg) of resistance. Safety eyes should be installed a maximum of six inches above the ground. Many garage door injuries, and nearly all garage door related property damage, can be avoided by following these precautions.
Extension spring systems should always be restrained by a safety cable that runs through the middle of the spring, tying off to a solid point at the rear and front of the horizontal door track. Extension springs represent a hazard to bystanders when a spring, pulley, or cable breaks under tension. Metal parts from extension spring systems can suddenly be launched.
Step 2: Check the tracks with a level to make sure they're properly aligned. Horizontal tracks should slant slightly down toward the back of the garage; with roll-up doors, the vertical sections of track should be exactly plumb. Both tracks must be at the same height on the garage walls. If the tracks are not properly aligned, loosen but do not remove the screws or bolts that hold the mounting brackets, and tap the tracks carefully into position. Recheck the tracks with the level to make sure they're in the right position; then tighten the screws or bolts at the mounting brackets.
If your garage door's spring breaks, stops working properly, or snaps, you'll lose the ability to open and close your garage door. This could happen due to a variety of issues, like normal wear and tear or from extreme temperature changes in a short amount of time. Spring replacements require a quick response from a garage door provider near you. Contact The Home Depot and a local, background-checked technician will respond within 24 hours.
Wood was the first material used in the manufacturing of garage doors. This type of material is still one of the most desired by homeowners. Individuals will find that garage doors that are constructed from wood can be painted or stained to match their home’s look. However, without regular maintenance, wood is susceptible to rot, decay and insect infestation.
Steel garage doors are one of the most durable options that can be chosen for the home. These doors should carry at least a 24 gauge rating for strength. Steel can be painted or purchased with a backed on finish that will complement the color scheme of a home’s exterior. Steel garage doors can be good deterrents for would be thieves that want to gain access to the home through the garage. Steel doors can be quite heavy due to the materials used to construct them.
Insulation, which increases energy efficiency and can help to lower utility bills, is crucial when a garage door is attached to the home. In this case, doors with high R-values are preferred. This means it has insulation that can keep the heat in. The higher the R-value, the better insulated your garage will be against outside noise and cold and hot air.
Install the stiffening strut on top of the top section of steel doors with the section lying flat. Then install the opener bracket that replaces the center bracket between the top two sections. While you’re working on the sections, protect them from scratches by putting carpet scraps on top of your sawhorses. Now, slide the rollers into the roller brackets.
Automatic doors require not only the installation of a heavy door, but the motor and cables as well. Automatic doors are much more common now because of their convenience, but in a case such as the heavy wood door, they are a necessity. A strong motor is required to pull up a heavy door. However, automatic doors are not without their faults -- they quickly become a manual door when the power goes out.