Just in case you still want to know: You could glue foam panels to the inside of the door, but it would be better to just pressure fit them in place to avoid the weight of the glue. Any weight that you add to the door has the very real potential to unbalance the door. If the springs were a little "hot" or strong to start with, it may not be a bad thing to add weight. If the springs were the right ones, even a few pounds will un-balance the door. If they were too weak to start with, any additional weight is going to make it worse.


After you’ve ordered your new garage door, we’ll perform a site inspection to confirm your door size. We’ll contact you to schedule the installation, and our professional installers will do the rest. They’ll deliver your door, take down the old door, reconnect your opener if there is one, seal your perimeter and provide a final walk-through where they’ll clean up the area and haul away your old door. Additional fees for haul away may apply in some markets. We are happy to provide answers to questions you may have at the time of your garage door and opener installation.
“Every spring on every garage door will break,” says Jim Rice, owner of Broad Ripple Overhead Doors & Openers in Indianapolis. “After so many thousand times up and down, it gets metal fatigue and snaps. At least once a year, you should disconnect the garage door springs and lift the door up manually to see how well it’s balanced. Unless you hear metal screeching or something breaks, you don’t need us.”
Question- I bought a Clopoy coachmen series 8' garage door last April , over the winter the bottom panel got a dent in it [snow blower-rock?] It is about the size of an egg . Called to see if any repair can be done instead of replacing[similar to dent wizard for autos and was advised cant be done and had to replace 3 panels? not going to do that- is there any other opinions on this?

An extension spring counterbalance system consists of a pair of stretched springs running parallel to the horizontal tracks. The springs lift the door through a system of pulleys and counterbalance cables running from the bottom corner brackets through the pulleys. When the door is raised, the springs contract, thus lifting the door as the tension is released. Typically these springs are made of 11 gauge galvanized steel, and the lengths of these springs are based on the height of the garage door in question. Their lifting weight capacity can best be identified by the color that is painted on the ends of the springs.

Response time was excellent. Alex was punctual, friendly, and knowledgeable. I had a 23 year old opener that I needed to replace. He came out and replaced it. It didn't take too long and he was professional in every way. I hope this new unit gives the service and longevity of the old one. We will see. From my experience with Precision Overhead Garage Door Service and Alex, I would use them again and I recommend them.read more
One aspect of hiring a garage door professional that differs, however, is emergency service. If you need after-hours or weekend service for a damaged or malfunctioning garage door or opener, be sure to ask your garage door contractor upfront about emergency service call fees, which can cost hundreds more than regular services. Unless it’s absolutely necessary, you may save significant money by scheduling garage door repairs and services during normal business hours.
Should an object or individual become trapped, or if a malfunction occurs, pulling on the handle will allow the user to manually lift the door up or down. If a garage door is good working order, the spring system that runs across the top of the door opening should provide enough assistance so an average adult can lift the door with relatively little effort.
Garage doors provide one of the major entryways into your home. Therefore, it is essential to ensure that they are secure and in good working order. If you are having problems with your current door, then you need to have a professional determine if it can be repaired or if it will need to be replaced. Here are some of the most common factors that will affect the cost of a garage door repair.
The lightweight design also causes a decrease in the insulation of these doors, so individuals that live in colder climates may want to consider other options for their garage door needs.  Fiberglass does not corrode when subjected to salt-water like some other door styles out there.  Individuals that live in coastal areas will find this feature beneficial for their needs.

All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.
Adding insulation to a hollow garage door can help heating and cooling costs and reduce noise. However, the most important thing to consider is how much weight you are adding to the door. The springs on a garage door are specific to the size and weight of the door, and adding weight to the door without changing the springs can damage them and wear out gears faster in the electric operator. Also, adding a strut across the door might be necessary to make sure the door doesn’t buckle when in the horizontal position.
Interested in garage door installation? You don’t have to know how to install a garage door or how to install a garage door opener. Lowe’s has you covered with professional, independent garage door installers to manage the job from taking measurements to the final garage door opener installation. Why take the time to learn how to install garage doors or how to install garage door openers? Invest less time and manage garage door installation costs. Contact Lowe’s for your project services today.
"Nathan was courteous and professional. He arrived on time and installed the garage door opener with no probelms. He tuned up our old garage door opener and installed it on our third car garage. He also added the new garage door opener to our cars for home link. I will call on Nathan for all my garage/ garage door opener needs and recommend him to my friends and neighbors."
A torsion spring counterbalance system consists of one or two tightly wound up springs on a steel shaft with cable drums at both ends. The entire apparatus mounts on the header wall above the garage door and has three supports: a center bearing plate with a steel or nylon bearing and two end bearing plates at both ends. The springs themselves consist of the steel wire with a stationary cone at one end and a winding cone at the other end. The stationary cone is attached to the center bearing plate. The winding cone consists of holes every 90 degrees for winding the springs and two set screws to secure the springs to the shaft. Steel counterbalance cables run from the roller brackets at the bottom corners of the door to a notch in the cable drums. When the door is raised, the springs unwind and the stored tension lifts the door by turning the shaft, thus turning the cable drums, wrapping the cables around the grooves on the cable drums. When the door is lowered, the cables unwrap from the drums and the springs are rewound to full tension.[7]
Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.
Containment cables. When old extension springs break, the springs and cables become heavy whips that damage cars and even injure people. To solve the whipping problem, manufacturers now offer containment cables that run through the center of side-mounted extension springs. If you have extension springs and don’t plan to replace your door, make sure the springs have these containment cables, or have a professional install them.
Call Precision for garage door repair in the Spokane area. We will send an expert garage door repair technician to your home that same day in order to repair your door on your schedule. Our technicians are experts in one area and one area alone: garages. Don’t stress over having to find a repairman who might not know garage doors all that well and trust your repairs to a company that guarantees the best service and parts in the business.
Installing an overhead garage door requires a few tools and a friend to help. First, the lower door panel needs to be set up in the center of the doorway. The remaining panels and tracks are held in place with hinges, brackets, and screws. Set up an easy-to-install torsion spring system to ensure that your door lifts properly for many years to come.
Step 2: Check the tracks with a level to make sure they're properly aligned. Horizontal tracks should slant slightly down toward the back of the garage; with roll-up doors, the vertical sections of track should be exactly plumb. Both tracks must be at the same height on the garage walls. If the tracks are not properly aligned, loosen but do not remove the screws or bolts that hold the mounting brackets, and tap the tracks carefully into position. Recheck the tracks with the level to make sure they're in the right position; then tighten the screws or bolts at the mounting brackets.
Garage doors cause injury and property damage (including expensive damage to the door itself) in several different ways. The most common causes of injury from garage door systems include falling doors, pinch points, improperly adjusted opener force settings and safety eyes, attempts at do-it-yourself repair without the proper knowledge or tools, and uncontrolled release of spring tension (on extension spring systems).

We had a garage door spring to break on a Friday afternoon. I called another company that I had used before and they said it would be Wednesday of next week for service. I then did the Web Search and found Precision Door and called them. They had a service person onsite that day before 6pm, replaced the broken spring and adjusted the door to close properly. I am very satisfied with the excellent response and service that Precision Door provided. I will use them again!!!

It is precisely on those coldest days of the year when you most need and appreciate the convenience of opening and closing your garage door quickly. Sadly, that's exactly the kind of day when moisture and cold can conspire to make this difficult. Garage doors can and do freeze to the garage floor. Sometimes it is just a minor icy connection between the two that can be broken when you hit the opener button. If the door refuses to budge on the first attempt, though, resist the urge to keep banging on the automatic opener button. This is likely to cause a more serious problem with the garage door opener—including, but not limited to, stripped gears, broken springs, and a burned-out motor on the opener.

Brian Printz showed up on time and was very polite and professional, He performed a complete door overhaul in less than an hour, during the door overhaul the rollers were replaced also, I will have to say II have never heard such a quiet door when lifting or closing. I am very happy. The price was a little more than expected but the way I look at it another spring will eventually brake and it will be covered under the lifetime warranty.
Very courteous and quick customer service! Andrew, Garage Door Consultant, responded within an hour and was at our house within two hours. We received a quote and placed an order approximately thirty minutes after his arrival. We received a phone call from Jessica in the Office confirming that our Door was ordered (three and a half hours after our initial call), and a promise to call back as soon as our door arrives at their warehouse to schedule the installation. The personnel are very professional and efficient instilling confidence we made a good decision to buy from Precision Door Service!Thanks Andrew and Jessica!read more
The Certified Technician, Rey Lopez, was competent, professional, polite, and willing to work. He quickly removed the old door and installed the new one. He then explained the vast differences between what we originally had and what we'd just purchased (stronger spring/tension rates; increased viability of door opening/closing life; beefier hardware; plastic vs. nylon rollers; stronger door reinforcement). Ray performed with alacrity his tasks and then demonstrated the quiet, solid way the door retracted--no banging after the initial rise from the ground. Finally, his attention to detail was so precise that he enabled another remote controlling all three doors, plus he capped some frayed wires, thus solving the problem of why the door opened intermittently. I would rate him a "6" on a scale of "1-5", meaning he went above and beyond our expectations. His "can do" attitude, coupled with the deference he showed, will take him a long, long way. May HaShem richly bless him in his endeavors!read more

Step 5: Check for loose hardware, and tighten as needed. On swing-up doors, check the plates where the spring is mounted to be sure the screws are tight, and tighten any loose screws. On roll-up doors, check the hinges that hold the sections of the door together; tighten any loose screws, and replace any damaged hinges. Sagging at one side of the door can often be corrected by servicing the hinges. If a screw hole is enlarged, replace the screw with a longer one of the same diameter, and use a hollow fiber plug, dipped in carpenters' glue, with the new screw. If the wood is cracked at a hinge, remove the hinge and fill the cracks and the screw holes with wood filler. Let the filler dry and then replace the hinge. If possible, move the hinge onto solid wood.
"Nathan was courteous and professional. He arrived on time and installed the garage door opener with no probelms. He tuned up our old garage door opener and installed it on our third car garage. He also added the new garage door opener to our cars for home link. I will call on Nathan for all my garage/ garage door opener needs and recommend him to my friends and neighbors."

Your garage door is the most-used exterior door to your home. And a garage door opener is the most common way of opening and closing the door. The opener makes access to your home safe and makes it easy to come and go so you want your opener to work smoothly and quietly all year long. We can repair your existing garage door opener or set you up with a brand new one, from a variety of fantastic brands! Call Precision today to schedule an appointment!
Since most yards entertain play activity including baseballs and other sporting equipment, it's no surprise that garage doors experience broken glass from time to time. Regardless of the cause, it's important to repair glass quickly, since broken glass in a garage is a safety issue, a security problem, and an invitation to every bird and insect in the neighborhood to take up residence in your garage. Fortunately, it's not difficult to replace a pane of glass. The techniques are exactly the same as for replacing glazing in a house window.
Sears garage repair technicians are fast, with same-day, emergency repairs available in most areas. We can replace garage door broken springs, rollers, cables, hinges, sensors and weather seals. We can also adjust garage door tracks and springs to make sure your door operates smoothly. Having problems with your garage door opener? We can repair or replace that too. Check out our line of Craftsman Garage Door Openers. Craftsman is America’s #1 brand of garage door openers! 1
Traditional One Panel: These doors consist of one large panel which tilts to open by employing a spring mechanism to swing upward. The wood version is popular in the South and Southeastern US, where a milder climate keeps the wood from rapidly deteriorating. Traditional garage door designs include Cape, Colonial, Ranch, Tudor and Craftsman. The disadvantage is these doors require a lot of clearance to operate correctly. Sometimes repairs can be difficult because of the heaviness of the door or its inaccessibility. Average cost to repair tilt-up doors is $172.
Instead, try other methods that might break the frozen connection between the door and the floor. For example, you can use a heat gun or hair dryer to melt the ice and free the door. Standard de-icing products can also work. And if you are careful not to damage the door or the seal on the bottom of the door, you can use a flat shovel or similar tool to chip away at the ice.

Having a balanced garage door is one of the most important aspects of how well your garage operates. A garage door that opens and closes smoothly reduces unnecessary strain on the door parts. Conversely, an unbalanced garage door can strip gears, overheat and shorten the life of your opener. A tune-up by Balanced Garage Doors will keep it running better longer, thereby, reducing your long-term costs for garage door repairs.
It can be hard to know whether you need a [previous_page anchor=”simple repair or a brand new door”]. That’s where GGD comes in. We offer free estimates, same-day service and will work closely with you to come up with the best solution for your budget. At Great Garage Door, we can service or find any garage door products that are presently made. We are also an original equipment manufacturer of our own product line: Endurance Door Inc. This means that we’re able to use the best components available, nationally to assemble products of outstanding quality at extremely competitive prices.
You can choose from three basic types of steel door: (1) steel only; (2) steel with insulation on the inside; and (3) steel on both sides with 1-3/8 to 2 in. of insulation. Other features that add to the cost are thicker insulation and windows, especially insulated windows. The do-it-yourself tensioning systems also add a little to the door’s cost. Be sure to specify exactly what you want.
You can choose from three basic types of steel door: (1) steel only; (2) steel with insulation on the inside; and (3) steel on both sides with 1-3/8 to 2 in. of insulation. Other features that add to the cost are thicker insulation and windows, especially insulated windows. The do-it-yourself tensioning systems also add a little to the door’s cost. Be sure to specify exactly what you want.

If the sensors are misaligned, or if there’s an obstruction blocking the beam from reaching the other side, the door won’t close without you forcing it. If you’re unable to realign the sensors on your own, or think it’s something else causing the problem, call a garage door repair technician. If he or she is able to realign the sensors and fix the problem, it shouldn’t cost you much more than a service call fee, which averages $50 to $75.
Regardless of the material, you will likely need to perform some regular maintenance tasks. A garage door professional can examine common problem areas to ensure all are working as they should. Additionally, it is necessary to examine the integrity of the door itself, since your garage can be especially vulnerable to security issues if your door is not structurally sound.
There is no cost because Precision will send a technician to your home for a "repair estimate". A "repair estimate" allows our technician to evaluate your garage door and determine why it is not functioning properly. Then provide you with a repair estimate with the cost to get your garage door operating correctly. The choice is yours to proceed with the work on the repair estimate or if you decide not to proceed with the work then there is no cost to you.
Our technicians are specially trained to handle a variety of garage brands, styles, and configurations. After arriving at your home, a Sears technician will diagnose the problem and walk you through the options for fixing it. Next, the technician will make any necessary adjustments or replace broken parts to ensure the door can be operational once again. We always attempt to complete repairs the same day of service, and your satisfaction is guaranteed. Our representatives are standing by for your call and are happy discuss pricing options.
Sears can fix almost any broken garage door opener, regardless of the brand or where you bought it. Trying to repair a garage door opener yourself can be dangerous because of the spring tension. The Sears technicians who repair garage door openers are experts; they have the knowledge and experience to repair the garage door opener correctly and safety.
I had Precision Doors come to my 1937 home to quote a new door to replace the original manual one. Service tech was prompt, patient, listened to my wishes to keep the house "old" in aesthetics, yet new and improved with the highest quality door they use. Joe, my tech, was phenomenal! He offered great advice and solutions to my situation, and even a better price all in. Confidence and trust was built in our very first meeting. The door was painstakingly installed with so many variables of old and new combinations. But Joe was amazing, and the door looks and operates flawlessly. Precision Door's top tier motor and door are the quietest I've ever witnessed. I feel so happy with my dealing with them. It was a great purchase and of the very best quality. One and done! And they offer a lifetime warranty on all of their work. It really can't be better. Have Precision Doors come to your home and you will be pleased that you did.read more
The Certified Technician, Rey Lopez, was competent, professional, polite, and willing to work. He quickly removed the old door and installed the new one. He then explained the vast differences between what we originally had and what we'd just purchased (stronger spring/tension rates; increased viability of door opening/closing life; beefier hardware; plastic vs. nylon rollers; stronger door reinforcement). Ray performed with alacrity his tasks and then demonstrated the quiet, solid way the door retracted--no banging after the initial rise from the ground. Finally, his attention to detail was so precise that he enabled another remote controlling all three doors, plus he capped some frayed wires, thus solving the problem of why the door opened intermittently. I would rate him a "6" on a scale of "1-5", meaning he went above and beyond our expectations. His "can do" attitude, coupled with the deference he showed, will take him a long, long way. May HaShem richly bless him in his endeavors!read more
The tech that serviced your door must not understand simple mechanics. The tracks do not move, so they do not need to be lubricated. All that does is make a mess. The rollers and hinges DO move, so it is logical to lubricate them, at the hinge barrel or pivot point, and in the little area near the stem of the rollers where you can see the bearings. Adding a bit of lube to the torsion spring also cuts down on the friction between the coils and makes the spring glide easier. However, too much will make it spritz out lube as the door opens and closes, and that it less than desirable. Same thing for pulleys on an extension spring door.
Single panel doors can also be installed with (one piece track type hardware) that folds the door back with a single horizontal track on each side (which is mounted at the top of the wood frame) and a roller, (mounted to the top of the door on each side. A hinge on each side that attaches to the bottom of each side of garage door. Using track hardware, a car can be parked much closer to the door, as the whole door, when in the open position, rests completely inside of the garage door header. Track type hardware has much less arc when raising and lowering the garage door as opposed jamb type hardware.[citation needed]
With hundreds of moving parts that are all required to work together, it's no surprise that garage doors may need occasional repair and maintenance. Garage door repair services are also required in emergency situations, like when the garage door won't operate and the car is trapped inside or you've accidentally backed into the door when it was closed. Whether it's a specific repair of your garage door opener, a broken spring that needs to be replaced, or a bent or rusted track, The Home Depot's local, licensed service providers can get the job done quickly and efficiently.
×