To help prevent garage door problems from occurring, the Institute of Door Dealer Education and Accreditation recommends monthly maintenance, including testing that the garage door opener is operational and inspection of the springs, rollers, pulleys, cables and track. Wipe down the tracks, preferably with a microfiber cloth to prevent lint from being left behind. Also, make sure to keep all the metal moving parts lubricated. However, do not lubricate plastic parts. Never reuse an old track with new panels.

Step 1: Check the metal tracks inside the garage. Look at the mounting brackets that hold the tracks to the walls. If they're loose, tighten the bolts or screws at the brackets. Working inside the garage with the garage door closed, examine the tracks for dents, crimps, or flat spots. If there are any damaged spots, pound them out with a rubber mallet, or with a hammer and a block of scrap wood. If the tracks are badly damaged, they should be replaced.
Automatic doors require not only the installation of a heavy door, but the motor and cables as well. Automatic doors are much more common now because of their convenience, but in a case such as the heavy wood door, they are a necessity. A strong motor is required to pull up a heavy door. However, automatic doors are not without their faults -- they quickly become a manual door when the power goes out.

Just in case you still want to know: You could glue foam panels to the inside of the door, but it would be better to just pressure fit them in place to avoid the weight of the glue. Any weight that you add to the door has the very real potential to unbalance the door. If the springs were a little "hot" or strong to start with, it may not be a bad thing to add weight. If the springs were the right ones, even a few pounds will un-balance the door. If they were too weak to start with, any additional weight is going to make it worse.


Sectional: Also known as a raised panel door, this door is the most common. It is made of several horizontal panels hinged together, fitted with wheels and mounted within a track. The biggest advantage of this door is it takes up relatively little space and easily controlled with a standard remote garage door opener for a nominal cost. Their moving parts are readily accessible which can keep repair costs low. The average cost for sectional door repairs is $128.
When you call on Precision Door, you can rest assured a talented professional will arrive at your home. Our technicians are professionally trained and field tested by the best in the industry at one of our two, state-of-the-art training facilities prior to servicing your door. Plus, successfully repairing over 1000 garage doors each day teaches you a lot. There is no substitute for experience
In order for you to find the right style door for your home, you need a tool that allows you to try out available options on a picture that approximates the look of your home. Using the Precision Door Designer, you'll easily create combinations of color, panel design and windows options that quickly educate you about the right style door for your home
An extension spring counterbalance system consists of a pair of stretched springs running parallel to the horizontal tracks. The springs lift the door through a system of pulleys and counterbalance cables running from the bottom corner brackets through the pulleys. When the door is raised, the springs contract, thus lifting the door as the tension is released. Typically these springs are made of 11 gauge galvanized steel, and the lengths of these springs are based on the height of the garage door in question. Their lifting weight capacity can best be identified by the color that is painted on the ends of the springs.

Repair Sagging Garage Doors – As doors and homes age, they can shift and move and sometimes this results in a garage door that needs to be realigned or reinforced. We will send a technician to your home to adjust the doors and to inspect the entire opening to make sure the door isn’t damaged. Once we understand the problem, we will fix the needed parts and make any adjustments to the door.

Get a price quote on a New Garage Door- Use our super-simple garage door designer to learn about the available options, pick the ones you like best, and send it to us for a free quote. It's the fastest way to shop for a garage door on the web. In less than 10 minutes, you'll have a much better idea what you want and get a price without sales pressure. Click garage door designer to get started...
Electric Garage Door Openers – Service and repair of the electric garage door opener itself, including the lift mechanism that pulls the door up and guides it down. This is typically not part of the garage door itself and is serviced and repaired on its own interval. Typical service includes inspection, repair, adjustment, and lubrication if needed. Also, we typically inspect the mounting of the unit as well as its attachment to the door itself.
A common material for a new garage door is steel sheet formed or stamped to look like a raised panel wooden door. Steel doors are available in uninsulated, insulated, and double skin steel. A design mimicking carriage house doors has become popular since early 2000s, and many manufacturers clad the exterior of a steel door with composite, vinyl boards, or other trim to give it the appearance of wood.
Our highly skilled technicians are specialists in every aspect of garage door repair including broken springs, rollers, and door remotes as well as garage door opener replacement and new door installation. We offer great prices and fast service in Buford, GA and throughout Gwinnett, North Fulton, Cobb, Cherokee, Forsyth, Hall, North DeKalb, Barrow, Bartow, Dawson, Gilmer, Gordon, Lumpkin, Pickens, Walton and Whitfield Counties.

Locating a contractor - there are many professional overhead garage door companies. It is always advisable to contact at least three different agencies and request a bid or quote for the work. Be sure that each quote includes the costs for a few different types of doors, any installation fees, and the cost of wiring the electronic openers. Standard prices range from:


Mike did an outstanding job replacing two torque-master spring assemblies for my double door garage. He arrived early, after calling to say he could do so, and offered a concise explanation of his very thorough safety inspection and diagnosis of my problem (one broken spring and another of suspect reliability). He then proceeded to swap out both torque masters with new torsion bar mechanisms in less than two hours. I found him personable, articulate, knowledgeable, and efficient. Honestly, my confidence in these newly installed devices has more to do with Mike than the products themselves. Thank you, Precision, for sending such a qualified professional to repair my garage doors. I will not hesitate to recommend your services to friends.read more

Overhead garage doors weigh hundreds of pounds, and doors that are not properly maintained or which are equipped with older automatic garage door openers can be safety time bombs. All too common are the tragic stories of garage doors injuring or even killing children or pets who found themselves underneath a closing door. Modern automatic door openers with auto-stop and auto-reverse mechanisms have greatly reduced such accidents, but mishaps can still occur if the door and door opener are not properly maintained.


Step 2: Check the tracks with a level to make sure they're properly aligned. Horizontal tracks should slant slightly down toward the back of the garage; with roll-up doors, the vertical sections of track should be exactly plumb. Both tracks must be at the same height on the garage walls. If the tracks are not properly aligned, loosen but do not remove the screws or bolts that hold the mounting brackets, and tap the tracks carefully into position. Recheck the tracks with the level to make sure they're in the right position; then tighten the screws or bolts at the mounting brackets.
The company is fantastic! Great customer service, quick and courteous response, knowledgeable repairman, quickly repaired, spent time confirming operability of door and opener and the price was more than reasonable. I recommend them heartily and would not use any other company than theirs for future issues, if any. Plus a 1 year warranty on service performed. they can't be beat as far as I am concerned. Ron K.
We have the best team of expert professionals who know how to handle each and every type of garage door and its components. This is because all of our technicians go through a rigorous training process, covering every known garage door repair technique. We do not let them onto the field until we know that they are completely trained, and can perform a job to perfection. Aside from this, they are continually updated with all the latest knowledge, information and training in order to do their work efficiently.
Technician gave me a window of 1-4pm, I called at 330 to see if he was on his way. He told me he would be there at 4pm, reason being was because of the amount of work orders he had that day. He was also by himself, had no helper. I was very satisfied that he was able to repair my garage door. He was very professional considering he showed up on a Friday afternoon on a 100 degree day. Thanks again
There are many lubricants out there but many garage door experts suggest using WD-40 (or similar light weight oil) twice a year to keep garage doors in working shape. All the moving parts of the door should be lubricated, including the hinges, the springs and the rollers. A bead of oil across the top of the springs will give a nice coating, and spraying the rollers is most effective. Also, it’s a good idea to check your garage door hardware for loose screws, nuts and bolts as you lubricate.
An extension spring counterbalance system consists of a pair of stretched springs running parallel to the horizontal tracks. The springs lift the door through a system of pulleys and counterbalance cables running from the bottom corner brackets through the pulleys. When the door is raised, the springs contract, thus lifting the door as the tension is released. Typically these springs are made of 11 gauge galvanized steel, and the lengths of these springs are based on the height of the garage door in question. Their lifting weight capacity can best be identified by the color that is painted on the ends of the springs.
Because garage door springs and openers can degrade over time, it’s important to occasionally test this safety feature. With the garage door open, place a solid object such as a 2-by-4 board or a cinder block where the door will close. Never test any safety feature using your or another person’s body. With the board or block in place, press the close button. If working properly, the garage door should close on the obstruction and immediately reverse the closing operation when it comes in contact with it.
×