Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
GREAT Company. Called in at 1:30 on a Saturday and my issue was fixed by 3:30 that same day. Our service tech Ken was a great guy who was A++++Can't ask for a better experience than I had with this company. I highly recommend this company and Ken to everyone. And their rates are very fair. GREAT Company to deal with. I wish any other contractor I've dealt with were even half as good as this company. A+++++++ all the way.read more
We know that you can oftentimes experience issues with your garage doors at the most inconven-ient times — sometimes in the worst weather and even during the odd hours at night. The thing is, these problems are not just inconvenient but can also be dangerous and cause accidents. That is why, we do not recommend hiring amateurs or adopting DIY solutions. We are available 24 hours, 7 days a week to address all your garage door needs. Our 24-Hour Emergency Garage Door Service comes with the highest quality service at the lowest possible price. What’s more, our technicians will give you on-site FREE cost estimates. To get the best value for your money, get in touch with us for your emergency garage door needs.
Here is an odd problem that I cannot figure out. I am handy with electrical stuff, but this one has me stumped. My small kitchen appliances all work on a single circuit, with 5 outlets. One of those outlets has a 20Amp breaker built into it with a test and resent button (I never understood what the test button is for). I only have a toaster, a floor lamp and occasionally a coffee grinder plugged into the circuit. Suddenly, none of the outlets work. Nothing new, no new appliances, the whole circuit went dead. I noticed when I trigger the reset button, there is an immediate click and it goes out again. I have tripped and reset the main breaker on the circuit board in the garage, nothing. Power gets to the outlet, but it doesn't work and there is no electricity in any of the 5. I un plugged everything. Reset the breaker on the outlet. It clicked again immediately, still no electricity. I changed out the outlet, with a new one with breaker built in which I bought today at Home Depot. Same problem. I tested for electricity, the outlet with the built in breaker receives 120v electricity coming in, but it always seems to be shorted out and does not send it out. I assume that all of the 5 outlets are connected inline, so thinking that if I went one by one, I'd be able to find a short. I opened all of the boxes, checked everything and all looks clean, new, no problems. I completely disconnected the two outlets that are closest to the main one with thereset button and nothing.Help
1. The up-limit switch may need to be moved toward the motor unit. This switch is usually a simply touch-lever mounted on the end of the track near the motor unit, and if it is too far ​away, the motor will stop the door before it fully opens. The solution is to move the switch closer to the motor unit. This is a somewhat rare problem, and will usually show itself immediately after a new garage door opener is installed.
The tech that serviced your door must not understand simple mechanics. The tracks do not move, so they do not need to be lubricated. All that does is make a mess. The rollers and hinges DO move, so it is logical to lubricate them, at the hinge barrel or pivot point, and in the little area near the stem of the rollers where you can see the bearings. Adding a bit of lube to the torsion spring also cuts down on the friction between the coils and makes the spring glide easier. However, too much will make it spritz out lube as the door opens and closes, and that it less than desirable. Same thing for pulleys on an extension spring door.
Garage doors provide one of the major entryways into your home. Therefore, it is essential to ensure that they are secure and in good working order. If you are having problems with your current door, then you need to have a professional determine if it can be repaired or if it will need to be replaced. Here are some of the most common factors that will affect the cost of a garage door repair.
First, we always provide a written estimate that is signed before doing any work, fully explaining what we'll do in plain English so you'll understand it. When we've completed the job, we walk you through and show you what's been done so you can be confident that your door was fixed right. We stand behind the job with the industry's best warranty and our 24 hour call back policy.

When your home or business depends on garage door repair in Bakersfield for everyday convenience, security, and dependability, the need for repairs can be a serious slowdown in your life. That’s why King Door Company offers Kern County residents and business the best garage door repairs and other services, completed by a team of expert professionals who can quickly and effectively fix garage doors in Bakersfield and the surrounding communities in Kern County.
Good response time and service; Question - I googled to find the Sears Garage Door repair phone number. During the conversation, I was unsure if this was "Sears" or a "contractor service" or other service. I had to ask if this repair person was coming from "Sears" or an independent repair. I was concerned until the service man arrived in a sears truck wearing Sears apparel. You might want the process to be more clearly identified as Sears. 

One aspect of hiring a garage door professional that differs, however, is emergency service. If you need after-hours or weekend service for a damaged or malfunctioning garage door or opener, be sure to ask your garage door contractor upfront about emergency service call fees, which can cost hundreds more than regular services. Unless it’s absolutely necessary, you may save significant money by scheduling garage door repairs and services during normal business hours.
A torsion spring counterbalance system consists of one or two tightly wound up springs on a steel shaft with cable drums at both ends. The entire apparatus mounts on the header wall above the garage door and has three supports: a center bearing plate with a steel or nylon bearing and two end bearing plates at both ends. The springs themselves consist of the steel wire with a stationary cone at one end and a winding cone at the other end. The stationary cone is attached to the center bearing plate. The winding cone consists of holes every 90 degrees for winding the springs and two set screws to secure the springs to the shaft. Steel counterbalance cables run from the roller brackets at the bottom corners of the door to a notch in the cable drums. When the door is raised, the springs unwind and the stored tension lifts the door by turning the shaft, thus turning the cable drums, wrapping the cables around the grooves on the cable drums. When the door is lowered, the cables unwrap from the drums and the springs are rewound to full tension.[7]
A garage door has a huge impact on your home. It’s the largest moving part of your home. it’s more than a garage door though, it’s also the second front door to your home. It enhances the curb appeal, energy efficiency, and security for your home. Don’t trust anyone else but the experts at Overhead Door Company of Pueblo™. We are the best garage door repair and service company in the Pueblo™ area, with the most experienced, professional, and courteous technicians.
Single panel doors are constructed from one monolithic panel. From the closed position a single panel door swings up and overhead with a hinge on each side (known as jamb type hardware) to the fully open position. A disadvantage of monolithic panel doors is that the swing up arc of the door occurs partially outside the garage. This means a vehicle must stop and park several feet in front of the door to avoid being hit by the garage door when it is opened.
If you've installed a replacement door or two around your home, it seems pretty simple -- all it takes is tightening a couple of screws and you're done. Installing t­he largest door in your house, however, is not quite so simple. Garage door in­stallation, whether manual or automatic, can be difficult and dangerous. Manual garage door installation is much easier than automatic garage door installation, but the one you choose generally depends on what kind of door you have.
If you have a steel door, but want the look of a wood one, it is not necessary to change your entire garage door. Often, it may be possible to mimic the look of wood with skillful painting. Your local home improvement store may be able to provide good advice about the type of paint and brushes needed to mimic the look of wood for your particular door material.
Whether you're planning on moving in the future or you're fixing up your forever home, replacing a garage door can provide an excellent return on investment and boost your home's resale value. According to Remodeling magazine's 2016 Cost vs. Value report, garage door upgrades provide a nationwide average return on investment of over 90%, making it one of the top five home improvement projects. To learn more about the cost of installing garage doors, visit our garage door and opener installation and repair cost guide.
Step 5: Check for loose hardware, and tighten as needed. On swing-up doors, check the plates where the spring is mounted to be sure the screws are tight, and tighten any loose screws. On roll-up doors, check the hinges that hold the sections of the door together; tighten any loose screws, and replace any damaged hinges. Sagging at one side of the door can often be corrected by servicing the hinges. If a screw hole is enlarged, replace the screw with a longer one of the same diameter, and use a hollow fiber plug, dipped in carpenters' glue, with the new screw. If the wood is cracked at a hinge, remove the hinge and fill the cracks and the screw holes with wood filler. Let the filler dry and then replace the hinge. If possible, move the hinge onto solid wood. 

Vinyl constructed garage doors are designed from the same materials as siding and window casements that you see on many homes.  This is a material that is lightweight and easy to work with.  Homeowners will find that vinyl is available in a wide range of color selections that will match the look of their home.  Vinyl can crack and bend out of shape if not properly taken care of.
"Nathan was courteous and professional. He arrived on time and installed the garage door opener with no probelms. He tuned up our old garage door opener and installed it on our third car garage. He also added the new garage door opener to our cars for home link. I will call on Nathan for all my garage/ garage door opener needs and recommend him to my friends and neighbors."
If you've installed a replacement door or two around your home, it seems pretty simple -- all it takes is tightening a couple of screws and you're done. Installing t­he largest door in your house, however, is not quite so simple. Garage door in­stallation, whether manual or automatic, can be difficult and dangerous. Manual garage door installation is much easier than automatic garage door installation, but the one you choose generally depends on what kind of door you have.
Roller doors ("Sheet Doors"-USA) are usually constructed of corrugated steel. They evolved from cover window and door coverings.[4] Other materials can be used (e.g.; transparent corrugated fibreglass) where strong impact resistance is not required. Corrugations give the door strength against impacts. A typical single car garage roller door has a preloaded spring inside the rolling mechanism. The spring reduces the effort required to open the door. Larger roller doors in commercial premises are not sprung (except USA) and use a manual pulley and chain system or a geared motor to raise and lower (roll up and roll down) the door. Roller doors cannot be effectively insulated.
×