Our highly skilled technicians are specialists in every aspect of garage door repair including broken springs, rollers, and door remotes as well as garage door opener replacement and new door installation. We offer great prices and fast service in Buford, GA and throughout Gwinnett, North Fulton, Cobb, Cherokee, Forsyth, Hall, North DeKalb, Barrow, Bartow, Dawson, Gilmer, Gordon, Lumpkin, Pickens, Walton and Whitfield Counties.
Mechanical garage door openers can pull or push a garage door with enough force to injure or kill people and pets if they become trapped. All modern openers are equipped with “force settings” that make the door reverse if it encounters too much resistance while closing or opening. Any garage door opener sold in the United States after 1992 requires safety eyes—sensors that prevent the door from closing if obstructed. Force settings should cause a door to stop or reverse on encountering more than approximately 20 lbs (9.07 kg) of resistance. Safety eyes should be installed a maximum of six inches above the ground. Many garage door injuries, and nearly all garage door related property damage, can be avoided by following these precautions.

I saw the plans during the Q&A of this proposed restructure and it seemed odd to me that the homeowners added a second story only above half of the house. I would think since they're must be spending around $700k for the project they should spend a little more and do the second floor above the whole house even if they only finish what is proposed now on the second floor they'd still have an unfinished area for the future home owners or for them to tackle when money is available. It would be a definite bump to the house value during the time of sale. Unless this has to do with zoning and FAR/lot size...
If your garage door's spring breaks, stops working properly, or snaps, you'll lose the ability to open and close your garage door. This could happen due to a variety of issues, like normal wear and tear or from extreme temperature changes in a short amount of time. Spring replacements require a quick response from a garage door provider near you. Contact The Home Depot and a local, background-checked technician will respond within 24 hours.
R-value describes the power of the insulation in your door. The higher the r-value, the stronger the insulation. Those doors will have better energy efficiency than doors that have a low r-value. Basic doors have an r-value of 0.0 with no insulation. The first step up gives you 1-3/8” insulation at a 6.5 rating. Next, a 1-3/8” thickness with Intellicore has a 12.9 r-value. The best option on the market is the 18.4 r-value, which has 2” Intellicore insulation.
If the sensors are misaligned, or if there’s an obstruction blocking the beam from reaching the other side, the door won’t close without you forcing it. If you’re unable to realign the sensors on your own, or think it’s something else causing the problem, call a garage door repair technician. If he or she is able to realign the sensors and fix the problem, it shouldn’t cost you much more than a service call fee, which averages $50 to $75.
Great Garage Door prides itself on providing [next_page anchor=”professional garage door repair and installation services”] in Monticello MN. We stand behind our warranties and guarantees to ensure that each and every client has a 5-Star experience and thinks of us when their friends and family have a garage door project. Call us today for a FREE estimate!

Call precision they came right over with in 30-45 minutes and give me my fee estimate... I was well pleased with what he said about the doors and how they are constructed plus he had some examples of what I will be getting ...also they are going to put my garage door openers up for free because I am buying there doors where other places will change you a lot of money....there not the cheapest place but you get what you pay for.....read more

Most good companies carry different quality parts. If someone can't afford to fix there door with the parts that will last long term, they will use standard parts that the door comes with. These can fail within 5 years. Better question is, how do you own a house, but can't afford $963 repair. A new HVAC can cost $10K. I wouldn't expect anyone to come to my house for less than $200. If I wasn't paying over $500 I would be questioning the quality of the repair and the credentials of the technician.


In need of garage door repair? Contact one of our many well-trained garage door repair professionals today to provide your garage door system with the recommended service and maintenance procedures for smooth and reliable operation. Doesn’t matter what the problem is, our garage door repair professionals are here for you! Are you looking to replace a garage door spring or searching for 'garage door repair near me'? Use our distributor locator below: 
When a garage door goes off the track, the spring breaks, the door is dented or the garage door opener is on the fritz, a professional garage door repair specialist can help. The cost to have a garage door fixed varies, but the national average cost of garage door repair is $70-$110. The extent of the damage and the size and material of the door will affect the final cost. A garage door repair company generally charges a national average of $80 for a service call, which includes the first hour of labor and service, such as testing and inspecting the garage door and opener. Apart from labor, the garage door repair costs hinge on buying replacements parts. For example, a new spring costs an average of $60. Expect to pay several hundred dollars, though, if the door is beyond repair; a new garage door ranges in price from $200 to $4,000, and most homeowners spend an average of $800-$1,200.
In addition to our damaged garage door repair services, we also provide and recommend preventative garage door maintenance in Bakersfield and communities throughout Kern County. Proactive maintenance is the best way to ensure your garage door is operating at its peak potential and that you put off costly repairs and replacement services as far into the future as possible.
10The type of garage door shown provides the necessary lift assistance with a “torque tube.” If you intend to use an opener, wait to install the tube. Otherwise, install the torque tube according to the manufacturer’s directions. Roll up the door about 4 feet to check for the alignment of the tracks, and make any adjustments. Then tighten all fasteners.
I'm not a professional, but I watched as my garage doors were serviced last year. The tech used a spray lubricant (I had bought a different brand in the garage door section of a home improvement store). He sprayed the inside of the entire track, top and bottom, the rollers that ride along the track, and all hinges on the door. He sprayed each hinge twice -- once on each side. The techs were more generous with the lubricant than I was when I'd done it before, so don't be afraid to give it a good squirt.
We know that you can oftentimes experience issues with your garage doors at the most inconven-ient times — sometimes in the worst weather and even during the odd hours at night. The thing is, these problems are not just inconvenient but can also be dangerous and cause accidents. That is why, we do not recommend hiring amateurs or adopting DIY solutions. We are available 24 hours, 7 days a week to address all your garage door needs. Our 24-Hour Emergency Garage Door Service comes with the highest quality service at the lowest possible price. What’s more, our technicians will give you on-site FREE cost estimates. To get the best value for your money, get in touch with us for your emergency garage door needs.
Single panel doors can also be installed with (one piece track type hardware) that folds the door back with a single horizontal track on each side (which is mounted at the top of the wood frame) and a roller, (mounted to the top of the door on each side. A hinge on each side that attaches to the bottom of each side of garage door. Using track hardware, a car can be parked much closer to the door, as the whole door, when in the open position, rests completely inside of the garage door header. Track type hardware has much less arc when raising and lowering the garage door as opposed jamb type hardware.[citation needed]
It's also possible that the circuit breaker, fuse, or GFCI controlling the door opener circuit has tripped or burned out. If you find that other lights or electrical circuits in the garage aren't operating, this is the likely cause, and you'll need to reset the breaker or GFCI or replace the burned-out fuse. If the circuit breaker or GFCI is tripping repeatedly, it's a sign that there is a short circuit somewhere in the system—possibly even the garage door opener itself. 
Because your garage door can be customized, pricing varies. Our Clopay configurator will help you review pricing as you begin your project. You’ll start with your door size and whether you need a single or double car door. Next, you can choose the collection of door, which gives you options of various materials and styles. Then, you’ll choose your construction, which allows you to decide what you need in terms of energy efficiency, durability and noise control. Lastly, you will be able to visualize the design and see an end price. Other optional add-ons include windows, decorative hardware, smart features and the r-value. However, you do not have to use the configurator. We also install standard garage doors that have not been customized so you know the product price early on in the process.
When it comes to installing garage doors and openers, The Home Depot has an unbeatable team of professionals dedicated to making sure your garage door project runs smoothly from start to finish. Your new garage door can be customized with a variety of features like unique color choices, window styles and hardware upgrades. We also offer options for your garage door opener including Smartphone control, Wi-Fi, battery back-up. The Home Depot installs garage doors and garage door openers with extended warranties that go beyond industry standards. Contact us today for a free in-home consultation.

Great!  We specialize in all sorts of garage door repair work.  Working around the garage door can be fairly dangerous if you’re trying to repair this issue on your own.  Most garage door companies will quickly remind folks about this, and it’s true.  Their are some hazards to watch out for when working around these heavy and high tension doors.  We recommend you give an expert a call to address the issue in a safe and timely manner for you.
Install the vertical roller tracks first by wrapping the curved lip around the rollers. The top of these tracks should be approximately 8 in. below the top of the top section. Wait to install the upper tracks until this step is complete. Check the level of the top section to make sure the tops of the vertical roller tracks are level with each other. The bottom of the roller tracks should be at least 1/8 in. off the concrete floor. After leveling and mounting these tracks, install the upper roller (horizontal) tracks.

On Monday afternoon the spring on our garage door snapped when the door came down after we had just backed out. As we were heading to a doctors appointment I did nothing about it until Tuesday morning. I called Precision Garage at about 8:30 am and their technician Aaron was at out home before 10am. He did a complete inspection and told us what was needed and also gave us an estimate on replacing the door as we have been thinking about that for sometime. He was very thorough and courteous. He explained everything to us. We decided to have new springs put in and order a new door. The springs were in within 20 minutes and we now have use of our door. They said it would be about three weeks for the new door to arrive and then they will install. We were blown away that we could get such quick service and so professional.There was no pressure and he went into detail about each kind of door that was available. Precision Garage is truly a great Thanksgiving gift for us. I'm anxious for the new door to come and I know we will love it.read more
Adding insulation to a hollow garage door can help heating and cooling costs and reduce noise. However, the most important thing to consider is how much weight you are adding to the door. The springs on a garage door are specific to the size and weight of the door, and adding weight to the door without changing the springs can damage them and wear out gears faster in the electric operator. Also, adding a strut across the door might be necessary to make sure the door doesn’t buckle when in the horizontal position.
Mechanical garage door openers can pull or push a garage door with enough force to injure or kill people and pets if they become trapped. All modern openers are equipped with “force settings” that make the door reverse if it encounters too much resistance while closing or opening. Any garage door opener sold in the United States after 1992 requires safety eyes—sensors that prevent the door from closing if obstructed. Force settings should cause a door to stop or reverse on encountering more than approximately 20 lbs (9.07 kg) of resistance. Safety eyes should be installed a maximum of six inches above the ground. Many garage door injuries, and nearly all garage door related property damage, can be avoided by following these precautions.
To make sure the job gets done right, our professional installers are local, licensed and insured. With a 9.7 out of 10 VOC score, our garage installers will exceed your expectations, provide reliable service, and install attractive garage doors that will transform your home’s appearance. All labor, products and installations are 100% backed by The Home Depot. Service you can trust.
All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.
We know that you can oftentimes experience issues with your garage doors at the most inconven-ient times — sometimes in the worst weather and even during the odd hours at night. The thing is, these problems are not just inconvenient but can also be dangerous and cause accidents. That is why, we do not recommend hiring amateurs or adopting DIY solutions. We are available 24 hours, 7 days a week to address all your garage door needs. Our 24-Hour Emergency Garage Door Service comes with the highest quality service at the lowest possible price. What’s more, our technicians will give you on-site FREE cost estimates. To get the best value for your money, get in touch with us for your emergency garage door needs.
Technician gave me a window of 1-4pm, I called at 330 to see if he was on his way. He told me he would be there at 4pm, reason being was because of the amount of work orders he had that day. He was also by himself, had no helper. I was very satisfied that he was able to repair my garage door. He was very professional considering he showed up on a Friday afternoon on a 100 degree day. Thanks again
I'm not a professional, but I watched as my garage doors were serviced last year. The tech used a spray lubricant (I had bought a different brand in the garage door section of a home improvement store). He sprayed the inside of the entire track, top and bottom, the rollers that ride along the track, and all hinges on the door. He sprayed each hinge twice -- once on each side. The techs were more generous with the lubricant than I was when I'd done it before, so don't be afraid to give it a good squirt.
If you've installed a replacement door or two around your home, it seems pretty simple -- all it takes is tightening a couple of screws and you're done. Installing t­he largest door in your house, however, is not quite so simple. Garage door in­stallation, whether manual or automatic, can be difficult and dangerous. Manual garage door installation is much easier than automatic garage door installation, but the one you choose generally depends on what kind of door you have.
In need of garage door repair? Contact one of our many well-trained garage door repair professionals today to provide your garage door system with the recommended service and maintenance procedures for smooth and reliable operation. Doesn’t matter what the problem is, our garage door repair professionals are here for you! Are you looking to replace a garage door spring or searching for 'garage door repair near me'? Use our distributor locator below: 
Ryan Fleming, Technician with Precision Door replaced a broken garage door spring at our home last night and I was so impressed with his knowledge, professionalism and positive attitude that I felt compelled to write this review. We have been customers of Precision Door for over 5 years and have always been pleased with how promptly and cost effectively they perform repair and maintenance work. I highly recommend both Ryan and Precision Door.read more
Just in case you still want to know: You could glue foam panels to the inside of the door, but it would be better to just pressure fit them in place to avoid the weight of the glue. Any weight that you add to the door has the very real potential to unbalance the door. If the springs were a little "hot" or strong to start with, it may not be a bad thing to add weight. If the springs were the right ones, even a few pounds will un-balance the door. If they were too weak to start with, any additional weight is going to make it worse.
GREAT Company. Called in at 1:30 on a Saturday and my issue was fixed by 3:30 that same day. Our service tech Ken was a great guy who was A++++Can't ask for a better experience than I had with this company. I highly recommend this company and Ken to everyone. And their rates are very fair. GREAT Company to deal with. I wish any other contractor I've dealt with were even half as good as this company. A+++++++ all the way.read more

Squealing, screeching, or grinding noises from your garage door are usually indicative of a lack of lubricant or an accumulation of dirt or debris in the tracks. When removing debris, do not use harsh chemicals to clean the tracks. Once the track is clean, coat it with lubricant designed especially for garage doors, if possible. If you do not have access to this special type of lubricant, you can use WD-40 on the tracks and hardware.


Home Depot local Service Providers are background checked, insured, licensed and/or registered. License or registration numbers held by or on behalf of Home Depot U.S.A., Inc. are available at homedepot.com/licensenumbers or at the Special Services Desk in The Home Depot store. State specific licensing information includes: AL 51289, 1924; AK 25084; AZ ROC252435, ROC092581; AR 228160518; CA 602331; CT HIC.533772; DC 420214000109, 410517000372; FL CRC046858, CGC1514813; GA RBCO005730, GCCO005540; HI CT-22120; ID RCE-19683; IA C091302; LA 43960, 557308, 883162; MD 85434, 42144; MA 112785, CS-107774; MI 2101089942, 2102119069; MN BC147263; MS 22222-MC; MT 37730; NE 26085; NV 38686; NJ 13VH09277500; NM 86302; NC 31521; ND 29073; OR 95843; The Home Depot U.S.A., Inc. is a Registered General Contractor in Rhode Island and its Registration Number is 9480; SC GLG110120; TN 47781; UT 286936-5501; VA 2705-068841; WA HOMED088RH; WV WV036104; WI 1046796.
If you have a steel door, but want the look of a wood one, it is not necessary to change your entire garage door. Often, it may be possible to mimic the look of wood with skillful painting. Your local home improvement store may be able to provide good advice about the type of paint and brushes needed to mimic the look of wood for your particular door material.
You can reschedule or cancel your service at any time. To reschedule, simply go to Your Orders, find your service order and click on the ‘Contact Provider’ button on Your Orders page. To cancel, click on the 'Cancel Order' button on Your Orders page. Payment goes to the pro from your secure Amazon account. Because you aren't charged until the actual work is completed, cancelling a job doesn't require a refund.
Ryan came to my rescue within 6 hrs of my call. He was professional, knowledgeable, friendly, and very thorough. He got my door up and running after figuring out what 3 others could not! Don’t try and go the cheapest route like I did because you’ll end up wasting time and money. Hire the pros like Ryan FIRST! If I ever need someone in the future, I’ll be calling them first thing! HIGHLY RECOMMENDread more
When you buy a new garage door, you are really hiring a garage door installation company. You will rely on that company for everything from advice on brands, insulation, material, features to an expert installation and may use them for years to come. You should be able to trust your garage door company with keeping you and your family safe and keeping your garage door working perfectly all year long. Let the experts at Precision Door show you why we are the best in the business, with our fast quality service, commercial grade parts, and friendly technicians you can trust.

This is the second time we have used this company. A year ad a half ago our spring broke on our single garage door and this week the spring broke on the double door. Each time a very neat young man came with excellent communication skiills and knowledge of the repair required. They arrive right on time and fixed it on the spot in a very timely manner at a fairly reasonable price. I have always been a person that never wanted to have a repairman come without my husband home. Based on the quality of the two employees I have had the pleaser of dealing with, that fear is unwarranted for this company.

Install the vertical roller tracks first by wrapping the curved lip around the rollers. The top of these tracks should be approximately 8 in. below the top of the top section. Wait to install the upper tracks until this step is complete. Check the level of the top section to make sure the tops of the vertical roller tracks are level with each other. The bottom of the roller tracks should be at least 1/8 in. off the concrete floor. After leveling and mounting these tracks, install the upper roller (horizontal) tracks.


Traditional One Panel: These doors consist of one large panel which tilts to open by employing a spring mechanism to swing upward. The wood version is popular in the South and Southeastern US, where a milder climate keeps the wood from rapidly deteriorating. Traditional garage door designs include Cape, Colonial, Ranch, Tudor and Craftsman. The disadvantage is these doors require a lot of clearance to operate correctly. Sometimes repairs can be difficult because of the heaviness of the door or its inaccessibility. Average cost to repair tilt-up doors is $172.
"Jeff and his brother replaced a broken Torsion Spring on my aluminum 2 car garage. I submitted my Service Magic request @9am on Saturday 1-19-08. Jeff called me back in less then 5 minutes, he came out to Parker on the same day and did not charge me for working on a Saturday! Jeff was on time, fast, clean and did a great job. Parts were high quality. The new spring was a higher quality then the spring the home builder used. Jeff even tweaked the adjustments on the opener and the garage door sounds better then it has in years. Price was right and I would use Jeff again. "

Automatic doors require not only the installation of a heavy door, but the motor and cables as well. Automatic doors are much more common now because of their convenience, but in a case such as the heavy wood door, they are a necessity. A strong motor is required to pull up a heavy door. However, automatic doors are not without their faults -- they quickly become a manual door when the power goes out.
Response time was excellent. Alex was punctual, friendly, and knowledgeable. I had a 23 year old opener that I needed to replace. He came out and replaced it. It didn't take too long and he was professional in every way. I hope this new unit gives the service and longevity of the old one. We will see. From my experience with Precision Overhead Garage Door Service and Alex, I would use them again and I recommend them.read more
The tech that serviced your door must not understand simple mechanics. The tracks do not move, so they do not need to be lubricated. All that does is make a mess. The rollers and hinges DO move, so it is logical to lubricate them, at the hinge barrel or pivot point, and in the little area near the stem of the rollers where you can see the bearings. Adding a bit of lube to the torsion spring also cuts down on the friction between the coils and makes the spring glide easier. However, too much will make it spritz out lube as the door opens and closes, and that it less than desirable. Same thing for pulleys on an extension spring door.
×