Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
1. The up-limit switch may need to be moved toward the motor unit. This switch is usually a simply touch-lever mounted on the end of the track near the motor unit, and if it is too far ​away, the motor will stop the door before it fully opens. The solution is to move the switch closer to the motor unit. This is a somewhat rare problem, and will usually show itself immediately after a new garage door opener is installed.
Garage door springs come in two styles: torsion (see above), which mounts on the header above the door, and extension (Photo 1), which floats above the upper roller track. In the past, extension springs were safer to install but didn’t have containment cables running through the center of the spring. Without cable, these springs become dangerous, heavy whips when they break. They also tend to be noisier than torsion springs, and we recommend you use them only if you don’t have the 12 in. of headroom above the door that a torsion spring requires.
The low rating on the CS is due to the fact that inwas out of town and my wife called because the garage door wouldn't open. We had repairs to the only other exit, and the CS said because it could be opened manually, it was no emergency. She was stuck in the house for over Sixteen hours. No emergency crew came out. Steve, a tech who came out the first time, fixed the door. It is not his fault CS took their sweet time to help a 45 year customer. I commend Steve. I do NOT have anything good to say about CS.
Containment cables. When old extension springs break, the springs and cables become heavy whips that damage cars and even injure people. To solve the whipping problem, manufacturers now offer containment cables that run through the center of side-mounted extension springs. If you have extension springs and don’t plan to replace your door, make sure the springs have these containment cables, or have a professional install them.
When your home or business depends on garage door repair in Bakersfield for everyday convenience, security, and dependability, the need for repairs can be a serious slowdown in your life. That’s why King Door Company offers Kern County residents and business the best garage door repairs and other services, completed by a team of expert professionals who can quickly and effectively fix garage doors in Bakersfield and the surrounding communities in Kern County.
"Jeff and his brother replaced a broken Torsion Spring on my aluminum 2 car garage. I submitted my Service Magic request @9am on Saturday 1-19-08. Jeff called me back in less then 5 minutes, he came out to Parker on the same day and did not charge me for working on a Saturday! Jeff was on time, fast, clean and did a great job. Parts were high quality. The new spring was a higher quality then the spring the home builder used. Jeff even tweaked the adjustments on the opener and the garage door sounds better then it has in years. Price was right and I would use Jeff again. "

To help prevent garage door problems from occurring, the Institute of Door Dealer Education and Accreditation recommends monthly maintenance, including testing that the garage door opener is operational and inspection of the springs, rollers, pulleys, cables and track. Wipe down the tracks, preferably with a microfiber cloth to prevent lint from being left behind. Also, make sure to keep all the metal moving parts lubricated. However, do not lubricate plastic parts. Never reuse an old track with new panels.


Step 2: Check the tracks with a level to make sure they're properly aligned. Horizontal tracks should slant slightly down toward the back of the garage; with roll-up doors, the vertical sections of track should be exactly plumb. Both tracks must be at the same height on the garage walls. If the tracks are not properly aligned, loosen but do not remove the screws or bolts that hold the mounting brackets, and tap the tracks carefully into position. Recheck the tracks with the level to make sure they're in the right position; then tighten the screws or bolts at the mounting brackets.
The lightweight design also causes a decrease in the insulation of these doors, so individuals that live in colder climates may want to consider other options for their garage door needs.  Fiberglass does not corrode when subjected to salt-water like some other door styles out there.  Individuals that live in coastal areas will find this feature beneficial for their needs.
Because garage door springs and openers can degrade over time, it’s important to occasionally test this safety feature. With the garage door open, place a solid object such as a 2-by-4 board or a cinder block where the door will close. Never test any safety feature using your or another person’s body. With the board or block in place, press the close button. If working properly, the garage door should close on the obstruction and immediately reverse the closing operation when it comes in contact with it.

Call Precision for garage door repair in the Spokane area. We will send an expert garage door repair technician to your home that same day in order to repair your door on your schedule. Our technicians are experts in one area and one area alone: garages. Don’t stress over having to find a repairman who might not know garage doors all that well and trust your repairs to a company that guarantees the best service and parts in the business.
Question- I bought a Clopoy coachmen series 8' garage door last April , over the winter the bottom panel got a dent in it [snow blower-rock?] It is about the size of an egg . Called to see if any repair can be done instead of replacing[similar to dent wizard for autos and was advised cant be done and had to replace 3 panels? not going to do that- is there any other opinions on this?
Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.

Because garage door springs and openers can degrade over time, it’s important to occasionally test this safety feature. With the garage door open, place a solid object such as a 2-by-4 board or a cinder block where the door will close. Never test any safety feature using your or another person’s body. With the board or block in place, press the close button. If working properly, the garage door should close on the obstruction and immediately reverse the closing operation when it comes in contact with it.
When you buy a new garage door, you are really hiring a garage door installation company. You will rely on that company for everything from advice on brands, insulation, material, features to an expert installation and may use them for years to come. You should be able to trust your garage door company with keeping you and your family safe and keeping your garage door working perfectly all year long. Let the experts at Precision Door show you why we are the best in the business, with our fast quality service, commercial grade parts, and friendly technicians you can trust.
Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.
Ricky appeared promptly at our appointment time, did a thorough safety inspection of our existing garage door opener, and explained the problems he found. Upon deciding to replace the door, he provided a complete and easy to follow set of options and samples from which to make our decision. Placing the order was a simple procedure, and Ricky was very knowledgeable and professional throughout our meeting with him.read more
Garage doors are the largest moving object inside your home. If you have a problematic garage door, it compromises the safety of your family and home. Overhead Door Company of Santa Fe™ is a professional company you can count on. We provide you with quality service at a reasonable price. We offer FREE estimates on replacement garage doors and are spring replacement specialists. 24 hours a day 7 days a week we are your number one garage door repair service.
If your garage door's spring breaks, stops working properly, or snaps, you'll lose the ability to open and close your garage door. This could happen due to a variety of issues, like normal wear and tear or from extreme temperature changes in a short amount of time. Spring replacements require a quick response from a garage door provider near you. Contact The Home Depot and a local, background-checked technician will respond within 24 hours.

All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.


Just in case you still want to know: You could glue foam panels to the inside of the door, but it would be better to just pressure fit them in place to avoid the weight of the glue. Any weight that you add to the door has the very real potential to unbalance the door. If the springs were a little "hot" or strong to start with, it may not be a bad thing to add weight. If the springs were the right ones, even a few pounds will un-balance the door. If they were too weak to start with, any additional weight is going to make it worse.
Looking to repair your garage door opener? Common problems could range from issues with the remote or wall switch that control the garage door opener to more serious issues like a grinding noise coming from the opener itself. If you need help with repairing your garage opener, schedule a repair appointment today! We repair all major brands and have same-day availability in most markets, so we can get your garage door opener repaired and running smoothly. To learn more about the cost of repairing garage doors, visit our garage door and opener installation and repair cost guide.

Garage Door Opener Company

×