Been a long time listener to WLAC and felt any advertisers they would present were reliable. Precision came quickly to determine what was need to fix my garage door for my car and a commercial size for my travel trailer. The technician was very knowledgeable and knew exactly what was needed to fix my doors. I recommend Precision for any garage door repair.
Mechanical garage door openers can pull or push a garage door with enough force to injure or kill people and pets if they become trapped. All modern openers are equipped with “force settings” that make the door reverse if it encounters too much resistance while closing or opening. Any garage door opener sold in the United States after 1992 requires safety eyes—sensors that prevent the door from closing if obstructed. Force settings should cause a door to stop or reverse on encountering more than approximately 20 lbs (9.07 kg) of resistance. Safety eyes should be installed a maximum of six inches above the ground. Many garage door injuries, and nearly all garage door related property damage, can be avoided by following these precautions.
Here is an odd problem that I cannot figure out. I am handy with electrical stuff, but this one has me stumped. My small kitchen appliances all work on a single circuit, with 5 outlets. One of those outlets has a 20Amp breaker built into it with a test and resent button (I never understood what the test button is for). I only have a toaster, a floor lamp and occasionally a coffee grinder plugged into the circuit. Suddenly, none of the outlets work. Nothing new, no new appliances, the whole circuit went dead. I noticed when I trigger the reset button, there is an immediate click and it goes out again. I have tripped and reset the main breaker on the circuit board in the garage, nothing. Power gets to the outlet, but it doesn't work and there is no electricity in any of the 5. I un plugged everything. Reset the breaker on the outlet. It clicked again immediately, still no electricity. I changed out the outlet, with a new one with breaker built in which I bought today at Home Depot. Same problem. I tested for electricity, the outlet with the built in breaker receives 120v electricity coming in, but it always seems to be shorted out and does not send it out. I assume that all of the 5 outlets are connected inline, so thinking that if I went one by one, I'd be able to find a short. I opened all of the boxes, checked everything and all looks clean, new, no problems. I completely disconnected the two outlets that are closest to the main one with thereset button and nothing.Help
We had a garage door spring to break on a Friday afternoon. I called another company that I had used before and they said it would be Wednesday of next week for service. I then did the Web Search and found Precision Door and called them. They had a service person onsite that day before 6pm, replaced the broken spring and adjusted the door to close properly. I am very satisfied with the excellent response and service that Precision Door provided. I will use them again!!!

Your garage door is the most-used exterior door to your home. And a garage door opener is the most common way of opening and closing the door. The opener makes access to your home safe and makes it easy to come and go so you want your opener to work smoothly and quietly all year long. We can repair your existing garage door opener or set you up with a brand new one, from a variety of fantastic brands! Call Precision today to schedule an appointment!
Jerrod the technician had answers to all my questions. He was very knowledgeable and very patiently explained what was going on with my garage door and the opener. I would definitely recommend A1 garage door service to friends and family. I was given options to either repair the door or replace it. I will get the door replaced when it gets non-functional from A1 garage door service.
The first safety feature is an automatic reversal system within the garage door opener itself. If the door is closing and an obstruction or solid object is detected – usually anything that slows or stops the door’s normal operation – the door should automatically stop and return to the open position. The U.S Consumer Product Safety Commission has required a reversing safety feature on all new garage door openers manufactured since 1991.
Commercial Door Spokane - a division of Precision Door Service. We specialize in the repair and maintenance of your commercial, industrial, and municipal doors, as well as fire doors and gates. Keep your doors open for business all year long with the best commercial parts and 24 hour service for whenever you need help. Trust your business in the hands of the experts at Precision Door and never settle for a garage door company that doesn’t have your best interests in mind.
Your garage door is the most-used exterior door to your home. And a garage door opener is the most common way of opening and closing the door. The opener makes access to your home safe and makes it easy to come and go so you want your opener to work smoothly and quietly all year long. We can repair your existing garage door opener or set you up with a brand new one, from a variety of fantastic brands! Call Precision today to schedule an appointment!

Should an object or individual become trapped, or if a malfunction occurs, pulling on the handle will allow the user to manually lift the door up or down. If a garage door is good working order, the spring system that runs across the top of the door opening should provide enough assistance so an average adult can lift the door with relatively little effort.


Step 1: Check the metal tracks inside the garage. Look at the mounting brackets that hold the tracks to the walls. If they're loose, tighten the bolts or screws at the brackets. Working inside the garage with the garage door closed, examine the tracks for dents, crimps, or flat spots. If there are any damaged spots, pound them out with a rubber mallet, or with a hammer and a block of scrap wood. If the tracks are badly damaged, they should be replaced.
Garage doors cause injury and property damage (including expensive damage to the door itself) in several different ways. The most common causes of injury from garage door systems include falling doors, pinch points, improperly adjusted opener force settings and safety eyes, attempts at do-it-yourself repair without the proper knowledge or tools, and uncontrolled release of spring tension (on extension spring systems). 

All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.


GREAT Company. Called in at 1:30 on a Saturday and my issue was fixed by 3:30 that same day. Our service tech Ken was a great guy who was A++++Can't ask for a better experience than I had with this company. I highly recommend this company and Ken to everyone. And their rates are very fair. GREAT Company to deal with. I wish any other contractor I've dealt with were even half as good as this company. A+++++++ all the way.read more
GREAT Company. Called in at 1:30 on a Saturday and my issue was fixed by 3:30 that same day. Our service tech Ken was a great guy who was A++++Can't ask for a better experience than I had with this company. I highly recommend this company and Ken to everyone. And their rates are very fair. GREAT Company to deal with. I wish any other contractor I've dealt with were even half as good as this company. A+++++++ all the way.read more
Another key safety feature to prevent entrapment from garage doors is the “electric eye” sensor system found on many more modern garage door systems. Sensors placed on either side of the garage door’s track system about 4 to 6 inches off the ground transmit an infrared beam of light during a door’s closing operation. Should anything break the beam during the closing operation – including adults, pets or other objects – the opener should automatically stop and reverse the closing operation.
Spring Issues - Unless it is due to an obstruction of some type, uneven movement of your garage door is likely caused by a problem with the spring mechanism. Roll-up doors generally have one center-mounted torsion spring. The tension on torsion springs is great. Therefore, it is necessary to call a professional for any repairs to this type of spring mechanism to avoid serious injury. Because replacement of these springs or cables in a garage door can take at least two or three hours of labor, costs can average $300 or more.

Repair Sagging Garage Doors – As doors and homes age, they can shift and move and sometimes this results in a garage door that needs to be realigned or reinforced. We will send a technician to your home to adjust the doors and to inspect the entire opening to make sure the door isn’t damaged. Once we understand the problem, we will fix the needed parts and make any adjustments to the door.
Great Garage Door provides quality garage door repair and installation services in Monticello MN. We know you have a lot of options when looking for a reliable service company, and that is why we have the best warranties and guarantees in the business. We stand behind our Minnesota products and services with over 30 years in the business and over 160,000 clients served.  We have a long list of happy clients that were once in your shoes and we’d like to learn how we can help you!
Just in case you still want to know: You could glue foam panels to the inside of the door, but it would be better to just pressure fit them in place to avoid the weight of the glue. Any weight that you add to the door has the very real potential to unbalance the door. If the springs were a little "hot" or strong to start with, it may not be a bad thing to add weight. If the springs were the right ones, even a few pounds will un-balance the door. If they were too weak to start with, any additional weight is going to make it worse.
I'm not a professional, but I watched as my garage doors were serviced last year. The tech used a spray lubricant (I had bought a different brand in the garage door section of a home improvement store). He sprayed the inside of the entire track, top and bottom, the rollers that ride along the track, and all hinges on the door. He sprayed each hinge twice -- once on each side. The techs were more generous with the lubricant than I was when I'd done it before, so don't be afraid to give it a good squirt.

Step 2: Check the tracks with a level to make sure they're properly aligned. Horizontal tracks should slant slightly down toward the back of the garage; with roll-up doors, the vertical sections of track should be exactly plumb. Both tracks must be at the same height on the garage walls. If the tracks are not properly aligned, loosen but do not remove the screws or bolts that hold the mounting brackets, and tap the tracks carefully into position. Recheck the tracks with the level to make sure they're in the right position; then tighten the screws or bolts at the mounting brackets.
This is the second time we have used this company. A year ad a half ago our spring broke on our single garage door and this week the spring broke on the double door. Each time a very neat young man came with excellent communication skiills and knowledge of the repair required. They arrive right on time and fixed it on the spot in a very timely manner at a fairly reasonable price. I have always been a person that never wanted to have a repairman come without my husband home. Based on the quality of the two employees I have had the pleaser of dealing with, that fear is unwarranted for this company.

With hundreds of moving parts that are all required to work together, it's no surprise that garage doors may need occasional repair and maintenance. Garage door repair services are also required in emergency situations, like when the garage door won't operate and the car is trapped inside or you've accidentally backed into the door when it was closed. Whether it's a specific repair of your garage door opener, a broken spring that needs to be replaced, or a bent or rusted track, The Home Depot's local, licensed service providers can get the job done quickly and efficiently.
After you’ve ordered your new garage door, we’ll perform a site inspection to confirm your door size. We’ll contact you to schedule the installation, and our professional installers will do the rest. They’ll deliver your door, take down the old door, reconnect your opener if there is one, seal your perimeter and provide a final walk-through where they’ll clean up the area and haul away your old door. Additional fees for haul away may apply in some markets. We are happy to provide answers to questions you may have at the time of your garage door and opener installation.
Great Garage Door provides quality garage door repair and installation services in Monticello MN. We know you have a lot of options when looking for a reliable service company, and that is why we have the best warranties and guarantees in the business. We stand behind our Minnesota products and services with over 30 years in the business and over 160,000 clients served.  We have a long list of happy clients that were once in your shoes and we’d like to learn how we can help you!

The low rating on the CS is due to the fact that inwas out of town and my wife called because the garage door wouldn't open. We had repairs to the only other exit, and the CS said because it could be opened manually, it was no emergency. She was stuck in the house for over Sixteen hours. No emergency crew came out. Steve, a tech who came out the first time, fixed the door. It is not his fault CS took their sweet time to help a 45 year customer. I commend Steve. I do NOT have anything good to say about CS.
First, we always provide a written estimate that is signed before doing any work, fully explaining what we'll do in plain English so you'll understand it. When we've completed the job, we walk you through and show you what's been done so you can be confident that your door was fixed right. We stand behind the job with the industry's best warranty and our 24 hour call back policy.
A garage door has a huge impact on your home. It’s the largest moving part of your home. it’s more than a garage door though, it’s also the second front door to your home. It enhances the curb appeal, energy efficiency, and security for your home. Don’t trust anyone else but the experts at Overhead Door Company of Pueblo™. We are the best garage door repair and service company in the Pueblo area, with the most experienced, professional, and courteous technicians. Our team of garage door technicians will repair all your broken springs, openers, and doors! When you’re ready to give your home a makeover, Overhead Door Company of Pueblo™ has the highest quality garage doors in the area.

Roller doors ("Sheet Doors"-USA) are usually constructed of corrugated steel. They evolved from cover window and door coverings.[4] Other materials can be used (e.g.; transparent corrugated fibreglass) where strong impact resistance is not required. Corrugations give the door strength against impacts. A typical single car garage roller door has a preloaded spring inside the rolling mechanism. The spring reduces the effort required to open the door. Larger roller doors in commercial premises are not sprung (except USA) and use a manual pulley and chain system or a geared motor to raise and lower (roll up and roll down) the door. Roller doors cannot be effectively insulated.

The first safety feature is an automatic reversal system within the garage door opener itself. If the door is closing and an obstruction or solid object is detected – usually anything that slows or stops the door’s normal operation – the door should automatically stop and return to the open position. The U.S Consumer Product Safety Commission has required a reversing safety feature on all new garage door openers manufactured since 1991.
Customer Satisfaction is our #1 priority. Above all, we take pride in providing a quick response time and aim to deliver a quality and cost-effective resolution to our customer's garage door repair needs be it morning, afternoon, or evening, 7 days a week. Our goal is to repair your garage doors and openers the same day so you can get back to your busy schedule.
If the sensors are misaligned, or if there’s an obstruction blocking the beam from reaching the other side, the door won’t close without you forcing it. If you’re unable to realign the sensors on your own, or think it’s something else causing the problem, call a garage door repair technician. If he or she is able to realign the sensors and fix the problem, it shouldn’t cost you much more than a service call fee, which averages $50 to $75.

In this article, we’ll tell you the difference between a safe door and one that’s unsafe. We’ll also give you the helpful tips you’re not likely to find in the manufacturer’s instructions to correctly, and safely, install a new garage door with a torsion spring and do-it-yourself tensioning. Installing a new, double garage door yourself will save you several hundred dollars and should take eight to 12 hours if you’re fairly handy. You can do most of the new garage door installation project yourself, but you should recruit help for removing the old door.
2. The safety sensors may need adjustment or realignment. Near the bottom of the door track on both sides are electronic eyes that require a clear line of view between them. If the sightlines are clear between the eyes, the door will close smoothly all the way to the floor. However, if anything is blocking the sightline, or if the brackets holding the electronic eyes are out of alignment, the door will fail to descend all the way. In most cases, the door will stop or reverse, and lights will flash to tell you there is a problem. 
×