Install the stiffening strut on top of the top section of steel doors with the section lying flat. Then install the opener bracket that replaces the center bracket between the top two sections. While you’re working on the sections, protect them from scratches by putting carpet scraps on top of your sawhorses. Now, slide the rollers into the roller brackets.
Given the complexity of a garage door and opener system, there are a variety of different areas something could go wrong. If your garage door shakes or is very loud during operation, the garage door closes all the way only to immediately open back up, the garage door opens slowly or closes too quickly, or the garage door opener and remote aren't working at all, you should seek help from a professional garage door repair specialist.
Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
If the sensors are misaligned, or if there’s an obstruction blocking the beam from reaching the other side, the door won’t close without you forcing it. If you’re unable to realign the sensors on your own, or think it’s something else causing the problem, call a garage door repair technician. If he or she is able to realign the sensors and fix the problem, it shouldn’t cost you much more than a service call fee, which averages $50 to $75.
Technician gave me a window of 1-4pm, I called at 330 to see if he was on his way. He told me he would be there at 4pm, reason being was because of the amount of work orders he had that day. He was also by himself, had no helper. I was very satisfied that he was able to repair my garage door. He was very professional considering he showed up on a Friday afternoon on a 100 degree day. Thanks again 

Insulation, which increases energy efficiency and can help to lower utility bills, is crucial when a garage door is attached to the home. In this case, doors with high R-values are preferred. This means it has insulation that can keep the heat in. The higher the R-value, the better insulated your garage will be against outside noise and cold and hot air.

The tech that serviced your door must not understand simple mechanics. The tracks do not move, so they do not need to be lubricated. All that does is make a mess. The rollers and hinges DO move, so it is logical to lubricate them, at the hinge barrel or pivot point, and in the little area near the stem of the rollers where you can see the bearings. Adding a bit of lube to the torsion spring also cuts down on the friction between the coils and makes the spring glide easier. However, too much will make it spritz out lube as the door opens and closes, and that it less than desirable. Same thing for pulleys on an extension spring door.
I'm not a professional, but I watched as my garage doors were serviced last year. The tech used a spray lubricant (I had bought a different brand in the garage door section of a home improvement store). He sprayed the inside of the entire track, top and bottom, the rollers that ride along the track, and all hinges on the door. He sprayed each hinge twice -- once on each side. The techs were more generous with the lubricant than I was when I'd done it before, so don't be afraid to give it a good squirt.
It’s been more than 30 years since we first started serving the Bakersfield area and all of Kern County, CA, and our approach has remained the same for these three-plus decades: we take care of your garage door needs as quickly and professionally as possible. Here’s a look at what you can expect when you choose King Door for Kern County garage door repair services:
The tech that serviced your door must not understand simple mechanics. The tracks do not move, so they do not need to be lubricated. All that does is make a mess. The rollers and hinges DO move, so it is logical to lubricate them, at the hinge barrel or pivot point, and in the little area near the stem of the rollers where you can see the bearings. Adding a bit of lube to the torsion spring also cuts down on the friction between the coils and makes the spring glide easier. However, too much will make it spritz out lube as the door opens and closes, and that it less than desirable. Same thing for pulleys on an extension spring door.
Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.

All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.


 I had Precision Doors come to my 1937 home to quote a new door to replace the original manual one. Service tech was prompt, patient, listened to my wishes to keep the house "old" in aesthetics, yet new and improved with the highest quality door they use. Joe, my tech, was phenomenal! He offered great advice and solutions to my situation, and even a better price all in. Confidence and trust was built in our very first meeting. The door was painstakingly installed with so many variables of old and new combinations. But Joe was amazing, and the door looks and operates flawlessly. Precision Door's top tier motor and door are the quietest I've ever witnessed. I feel so happy with my dealing with them. It was a great purchase and of the very best quality. One and done! And they offer a lifetime warranty on all of their work. It really can't be better. Have Precision Doors come to your home and you will be pleased that you did.read more 

In need of garage door repair? Contact one of our many well-trained garage door repair professionals today to provide your garage door system with the recommended service and maintenance procedures for smooth and reliable operation. Doesn’t matter what the problem is, our garage door repair professionals are here for you! Are you looking to replace a garage door spring or searching for 'garage door repair near me'? Use our distributor locator below: 
"Nathan was courteous and professional. He arrived on time and installed the garage door opener with no probelms. He tuned up our old garage door opener and installed it on our third car garage. He also added the new garage door opener to our cars for home link. I will call on Nathan for all my garage/ garage door opener needs and recommend him to my friends and neighbors."
Instead, try other methods that might break the frozen connection between the door and the floor. For example, you can use a heat gun or hair dryer to melt the ice and free the door. Standard de-icing products can also work. And if you are careful not to damage the door or the seal on the bottom of the door, you can use a flat shovel or similar tool to chip away at the ice.
Here is an odd problem that I cannot figure out. I am handy with electrical stuff, but this one has me stumped. My small kitchen appliances all work on a single circuit, with 5 outlets. One of those outlets has a 20Amp breaker built into it with a test and resent button (I never understood what the test button is for). I only have a toaster, a floor lamp and occasionally a coffee grinder plugged into the circuit. Suddenly, none of the outlets work. Nothing new, no new appliances, the whole circuit went dead. I noticed when I trigger the reset button, there is an immediate click and it goes out again. I have tripped and reset the main breaker on the circuit board in the garage, nothing. Power gets to the outlet, but it doesn't work and there is no electricity in any of the 5. I un plugged everything. Reset the breaker on the outlet. It clicked again immediately, still no electricity. I changed out the outlet, with a new one with breaker built in which I bought today at Home Depot. Same problem. I tested for electricity, the outlet with the built in breaker receives 120v electricity coming in, but it always seems to be shorted out and does not send it out. I assume that all of the 5 outlets are connected inline, so thinking that if I went one by one, I'd be able to find a short. I opened all of the boxes, checked everything and all looks clean, new, no problems. I completely disconnected the two outlets that are closest to the main one with thereset button and nothing.Help
If you have a steel door, but want the look of a wood one, it is not necessary to change your entire garage door. Often, it may be possible to mimic the look of wood with skillful painting. Your local home improvement store may be able to provide good advice about the type of paint and brushes needed to mimic the look of wood for your particular door material.
Squealing, screeching, or grinding noises from your garage door are usually indicative of a lack of lubricant or an accumulation of dirt or debris in the tracks. When removing debris, do not use harsh chemicals to clean the tracks. Once the track is clean, coat it with lubricant designed especially for garage doors, if possible. If you do not have access to this special type of lubricant, you can use WD-40 on the tracks and hardware.
I'm not a professional, but I watched as my garage doors were serviced last year. The tech used a spray lubricant (I had bought a different brand in the garage door section of a home improvement store). He sprayed the inside of the entire track, top and bottom, the rollers that ride along the track, and all hinges on the door. He sprayed each hinge twice -- once on each side. The techs were more generous with the lubricant than I was when I'd done it before, so don't be afraid to give it a good squirt.
Most garage doors have two springs installed, when one breaks it's safe to say the second spring's life expectancy has just about expired. In order to save you from future inconvenience, unsafe garage door practices, and damaging your garage door opener, Precision will usually recommend to replace both springs. If you've had the same tires on your car for a while and one blows out while you're driving, wouldn't you replace them both? It's extremely important to properly maintain equipment such as garage doors and automobiles.

Annual maintenance. Make an annual check of all nuts and bolts on rails and rollers to make sure they’re firmly tightened. Check the condition of all cables to make sure they’re not worn or frayed. Lubricate rollers and springs with a garage-door lubricant (see How to Fix a Noisy Garage Door for maintenance and problem-solving tips). The door should operate smoothly and be properly balanced. Check the balance by disconnecting the opener and lowering the door halfway- the door should hold its position. If it doesn’t, adjust the spring tension or replace the springs.


In this article, we’ll tell you the difference between a safe door and one that’s unsafe. We’ll also give you the helpful tips you’re not likely to find in the manufacturer’s instructions to correctly, and safely, install a new garage door with a torsion spring and do-it-yourself tensioning. Installing a new, double garage door yourself will save you several hundred dollars and should take eight to 12 hours if you’re fairly handy. You can do most of the new garage door installation project yourself, but you should recruit help for removing the old door.
When you have an urgent garage door issue, call our 24-hour emergency service for assistance. Can’t schedule an appointment for someone to come out later in the week, and can’t sit around waiting for a repair service provider to show up long after the scheduled time? That’s why King Door provides same-day garage door repair in Bakersfield and throughout Kern County.
Your garage door is more than just a point of entry for vehicles; it also protects your greatest investment and has a huge impact on your home’s overall curb appeal. So don’t let a worn-down, barely functioning garage door interfere with the form or function of your home! Instead, get in touch with Aladdin Garage Doors today for the reliable garage door repair services your home needs.
Because your garage door can be customized, pricing varies. Our Clopay configurator will help you review pricing as you begin your project. You’ll start with your door size and whether you need a single or double car door. Next, you can choose the collection of door, which gives you options of various materials and styles. Then, you’ll choose your construction, which allows you to decide what you need in terms of energy efficiency, durability and noise control. Lastly, you will be able to visualize the design and see an end price. Other optional add-ons include windows, decorative hardware, smart features and the r-value. However, you do not have to use the configurator. We also install standard garage doors that have not been customized so you know the product price early on in the process.

Garage doors cause injury and property damage (including expensive damage to the door itself) in several different ways. The most common causes of injury from garage door systems include falling doors, pinch points, improperly adjusted opener force settings and safety eyes, attempts at do-it-yourself repair without the proper knowledge or tools, and uncontrolled release of spring tension (on extension spring systems).
Since most yards entertain play activity including baseballs and other sporting equipment, it's no surprise that garage doors experience broken glass from time to time. Regardless of the cause, it's important to repair glass quickly, since broken glass in a garage is a safety issue, a security problem, and an invitation to every bird and insect in the neighborhood to take up residence in your garage. Fortunately, it's not difficult to replace a pane of glass. The techniques are exactly the same as for replacing glazing in a house window.
 Very courteous and quick customer service! Andrew, Garage Door Consultant, responded within an hour and was at our house within two hours. We received a quote and placed an order approximately thirty minutes after his arrival. We received a phone call from Jessica in the Office confirming that our Door was ordered (three and a half hours after our initial call), and a promise to call back as soon as our door arrives at their warehouse to schedule the installation. The personnel are very professional and efficient instilling confidence we made a good decision to buy from Precision Door Service!Thanks Andrew and Jessica!read more 

Garage Door Installation – This includes the installation of a new garage door. Includes the door itself, the track, cables, springs, hinges, handles, locks and rollers.  It is the complete service and installation of a new door. We inspect all the parts, make adjustments to fit your garage opening, and service all elements during the installation process. Plus, we check to ensure all parts are in proper working order after installed.
Aluminum garage door styles are similar to steel doors except that they weigh much less.  This prevents them from providing a great deal of insulation and they do tend to dent easily.  However, Aluminum is one of the least expensive garage doors that can be purchased for the home, they have a long lasting finish that does not rust easily and it is available in a faux wood texture that can complement the home’s overall look.

Step 2: Check the tracks with a level to make sure they're properly aligned. Horizontal tracks should slant slightly down toward the back of the garage; with roll-up doors, the vertical sections of track should be exactly plumb. Both tracks must be at the same height on the garage walls. If the tracks are not properly aligned, loosen but do not remove the screws or bolts that hold the mounting brackets, and tap the tracks carefully into position. Recheck the tracks with the level to make sure they're in the right position; then tighten the screws or bolts at the mounting brackets.


Carriage: These doors mimic the look of doors found on old carriage houses in the days of horses and buggies. Because of their rustic look, they are often favored in the West and Southwest of the United States. The doors swing open like oversized French doors and hang from jambs on hinges. With their unique look, they create an area of visual interest for your home and are quite energy efficient. The downside is they require a considerable amount of clearance to work properly. Because most carriage garage doors are largely composed of wood, you may need to replace deteriorating or rotting door materials. The average cost for carriage garage door repairs is $133.
Not only was the upward-lifting garage door and the electric garage door opener invented by Overhead Door Corporation’s founder C.G Johnson in the 1920s, but we also have a tradition in excellence for garage door repair, service and maintenance. Even with the most reliable products problems can arise and when they do it’s important to know who to contact to fix these issues while providing solutions to prevent future complications.
You can choose from three basic types of steel door: (1) steel only; (2) steel with insulation on the inside; and (3) steel on both sides with 1-3/8 to 2 in. of insulation. Other features that add to the cost are thicker insulation and windows, especially insulated windows. The do-it-yourself tensioning systems also add a little to the door’s cost. Be sure to specify exactly what you want.
2. The safety sensors may need adjustment or realignment. Near the bottom of the door track on both sides are electronic eyes that require a clear line of view between them. If the sightlines are clear between the eyes, the door will close smoothly all the way to the floor. However, if anything is blocking the sightline, or if the brackets holding the electronic eyes are out of alignment, the door will fail to descend all the way. In most cases, the door will stop or reverse, and lights will flash to tell you there is a problem. 
×